Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Audio/Video/Electronics Forum [GEN 1]
CB Part 2 - coax routing
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="MarkT" data-source="post: 86656" data-attributes="member: 3007"><p>Dan, </p><p></p><p>Open both doors on the driver's side. Remove the door sill plastic trim. The grommet is about in the middle of the rear door opening. You can't miss it. The grommet is easy to remove. Then go under the truck and you'll be able to see the hole. These were the best pics I could take.</p><p></p><p>In the pics you can see the edge of the carpet. I just ran the coax under the carpet near the front of the seat and routed it to a hole where some existing wiring comes up under the seat already. My camera refuses to take a pic under the seat so I can't get a good shot of it. Or you could run the coax all the way forward down the channel and bring it up under the dash. Or you could run the coax behind the driver's seat under the carpet over to the center console. Once you start looking at it, I'm sure you'll be able to figure something out depending on where you plan to mount the radio.</p></blockquote><p></p>
[QUOTE="MarkT, post: 86656, member: 3007"] Dan, Open both doors on the driver's side. Remove the door sill plastic trim. The grommet is about in the middle of the rear door opening. You can't miss it. The grommet is easy to remove. Then go under the truck and you'll be able to see the hole. These were the best pics I could take. In the pics you can see the edge of the carpet. I just ran the coax under the carpet near the front of the seat and routed it to a hole where some existing wiring comes up under the seat already. My camera refuses to take a pic under the seat so I can't get a good shot of it. Or you could run the coax all the way forward down the channel and bring it up under the dash. Or you could run the coax behind the driver's seat under the carpet over to the center console. Once you start looking at it, I'm sure you'll be able to figure something out depending on where you plan to mount the radio. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
EL Snagadore
BushwiickBill
jekyll537
New recaros
Spike Spiegel
basstheman
GaoKS
doyouthinkhesawus
ToadSmasher2K1
raptorgroyper
Reptar854
zachery55
Gen1Roush
AZ Raptor
Badboy4fun_wa
Matt Pearlman
DFS
Johnny@Apollo-Optics
t34ddd
toys
Mrjoshiba
PD1744
rschap1
Bsbuggs
cjhoneyman
Jbultz1
Morgan
Dano182
mario500
WatFam
Sharpie69
Hard R
jhamiltonak
wheelman55
RogueClimber
TomDirt
HookEm
jdm_sixtwo
RLB18
Canuck714
Arizona Free
laramie1pt8t
Raptor812
nikhsub1
RRick
scsponger31
Jakenbake
k3k0a808
Advcgh
raptrrr
... and 34 more.
Forum statistics
Threads
93,206
Posts
1,955,979
Members
56,485
Latest member
bjorn-dpc
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Audio/Video/Electronics Forum [GEN 1]
CB Part 2 - coax routing
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top