Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Exhaust and Cutouts Discussion [GEN 1]
Stainless Works Dual Under Bumper Exit Installed
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Shekkie2432" data-source="post: 1696715" data-attributes="member: 49279"><p>I found the stock exhaust a bit quiet for my liking so after many YouTube videos and reading most posts here I decided to go with a Stainless Works system (factory connect) with the exit under bumper. I like things symmetrical was the main reason for the exit choice. I’m a weirdo that way.</p><p></p><p>Good? The system seems to be of quality…..welds are good, hangers appear heavy duty. The whole thing feels stout. I ordered direct from them and customer service was excellent. The sound is just what I was after……a bit of a rumble and strong v8 tone when accelerating, no drone, very near stock sounding from the interior when cruising. Perfect. I tucked the polished stainless tips under the bumper a bit so not much to look at from behind. I may make them more obvious later, I can’t decide.</p><p></p><p>Not so good? The installation instructions are an embarrassment. If I haven’t been working on cars/trucks for most of my life and didn’t have access to this forum and google I woulda been in trouble. It’s not like it’s a direct replacement system. There are four hangers to figure out with zero help from the instructions. Ultimately it wasn’t too much hassle to figure out but I shouldn’t have been left on my own to do it. The overall fit is excellent with the exception of the pipe that exits on the left side of the bumper. To get it level I had to make a rubber spacer to lower the front of my spare about an inch. Not that big of a deal and I understand it’s a tight fit and all of these trucks are a tiny bit different. I may take a bit out of one of the pipes to correct this later but it’s not a priority.</p><p></p><p>I am super pleased, would purchase again and recommend it if your goals are similar to mine. [ATTACH=full]327096[/ATTACH][ATTACH=full]327097[/ATTACH][ATTACH=full]327099[/ATTACH][ATTACH=full]327102[/ATTACH]</p></blockquote><p></p>
[QUOTE="Shekkie2432, post: 1696715, member: 49279"] I found the stock exhaust a bit quiet for my liking so after many YouTube videos and reading most posts here I decided to go with a Stainless Works system (factory connect) with the exit under bumper. I like things symmetrical was the main reason for the exit choice. I’m a weirdo that way. Good? The system seems to be of quality…..welds are good, hangers appear heavy duty. The whole thing feels stout. I ordered direct from them and customer service was excellent. The sound is just what I was after……a bit of a rumble and strong v8 tone when accelerating, no drone, very near stock sounding from the interior when cruising. Perfect. I tucked the polished stainless tips under the bumper a bit so not much to look at from behind. I may make them more obvious later, I can’t decide. Not so good? The installation instructions are an embarrassment. If I haven’t been working on cars/trucks for most of my life and didn’t have access to this forum and google I woulda been in trouble. It’s not like it’s a direct replacement system. There are four hangers to figure out with zero help from the instructions. Ultimately it wasn’t too much hassle to figure out but I shouldn’t have been left on my own to do it. The overall fit is excellent with the exception of the pipe that exits on the left side of the bumper. To get it level I had to make a rubber spacer to lower the front of my spare about an inch. Not that big of a deal and I understand it’s a tight fit and all of these trucks are a tiny bit different. I may take a bit out of one of the pipes to correct this later but it’s not a priority. I am super pleased, would purchase again and recommend it if your goals are similar to mine. [ATTACH type="full" alt="5BEFEA88-389E-48DD-A432-97B81D93CFC5.jpeg"]327096[/ATTACH][ATTACH type="full" alt="15E52969-4C96-4E39-B26F-AA40A20E6EF9.jpeg"]327097[/ATTACH][ATTACH type="full" alt="8F603456-181E-4895-AE2D-6E04D63BA5D8.jpeg"]327099[/ATTACH][ATTACH type="full" alt="716EB73F-94B0-488C-822D-C1747601F88B.jpeg"]327102[/ATTACH] [/QUOTE]
Insert quotes…
Verification
Post reply
Staff online
Big Blue
Administrator
Members online
blazn5667
NES431
julien194b
MZRaptor72
Zeusmotorworks
PilotsWreck
PK37
Big Blue
shank_guru
EricM
Derek50
Bruno Marques
hamster
CecilK12
dvm
Jesse1983
TomDirt
jdm_sixtwo
Bozz
Advcgh
Forum statistics
Threads
93,180
Posts
1,955,522
Members
56,460
Latest member
khunter
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Exhaust and Cutouts Discussion [GEN 1]
Stainless Works Dual Under Bumper Exit Installed
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top