Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford F-150 Raptor General Discussions [GEN 2]
Husky Wheel Arch Liners on 2019
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Terry" data-source="post: 1414674" data-attributes="member: 37028"><p>The liners came with one screw per side (total of two) which are sufficient. The existing fasteners on the wheel flares are reused for the installation. The liners fit snugly and they won't be going anywhere once installed. I don't have pictures of the holes I drilled and enlarged but they are the both at the bottom, rear of the liner where the wheel flares overlap the liner. You won't have any problem figuring that out once the liner is fitted into place. the liner fits in between the existing wheel flares and the fender itself. I don't see any reason to have to trim the liners as some have done - they don't exert any pressure on the wheel flares and they won't cause any problems. The one screw per side fits into a 'u-clip' that fits over an existing hole in the wheel well. the 'u-clip' is steel and needs to be insulated from the aluminum body to prevent electrolysis. I placed three layers of clear, plastic packing tape on the aluminum before sliding the 'u-clip' into place so there would never be any problems. I also took the rear wheel off on each side to do the install. I drilled the holes needed after the liners were in place and there isn't any room for the drill with the tires still on the truck. The instructions that come with the liners are good so you'll know how to proceed. Hope that helps.</p></blockquote><p></p>
[QUOTE="Terry, post: 1414674, member: 37028"] The liners came with one screw per side (total of two) which are sufficient. The existing fasteners on the wheel flares are reused for the installation. The liners fit snugly and they won't be going anywhere once installed. I don't have pictures of the holes I drilled and enlarged but they are the both at the bottom, rear of the liner where the wheel flares overlap the liner. You won't have any problem figuring that out once the liner is fitted into place. the liner fits in between the existing wheel flares and the fender itself. I don't see any reason to have to trim the liners as some have done - they don't exert any pressure on the wheel flares and they won't cause any problems. The one screw per side fits into a 'u-clip' that fits over an existing hole in the wheel well. the 'u-clip' is steel and needs to be insulated from the aluminum body to prevent electrolysis. I placed three layers of clear, plastic packing tape on the aluminum before sliding the 'u-clip' into place so there would never be any problems. I also took the rear wheel off on each side to do the install. I drilled the holes needed after the liners were in place and there isn't any room for the drill with the tires still on the truck. The instructions that come with the liners are good so you'll know how to proceed. Hope that helps. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
MurderedOutSVT
elpechedepeche
LayinWatts69
foundations
ToadSmasher2K1
WH7
KAJRIP
nelsonr103
TheGrizz
GordoJay
Jorge Acosta
Cobraman044
P4SHOCAT
catinthehat85
Controlsguy21
snt505
bakwaas4eva
v2500hd
cuts
krmzn
nemx735
Old-Raptor-guy
eanevarez
Coyote_695
4xfun
24NoVARaptor
3Dog
OrangemanOtto
gt942nv00
sambhutta
jgsmithsae
HORN HIGH ACES
gatorbyteme
Hambone
RaptorMach3p5
MidnightSpecial
debauch
hingedthinker
kevo_lo
Todd Turbo S
XSTNKT
WhiskeyTangoGTFO
970rap
Keamg5
Turning Blue
DFS
Fire Ball
BenBB
RLB18
Irregular F150
... and 41 more.
Forum statistics
Threads
93,201
Posts
1,955,904
Members
56,485
Latest member
bjorn-dpc
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford F-150 Raptor General Discussions [GEN 2]
Husky Wheel Arch Liners on 2019
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top