Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 2]
GJ Motorsports 3rd brakelight/chase light install video
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="nikhsub1" data-source="post: 1478573" data-attributes="member: 22952"><p>I've had my light since it the first batch that GJ made - it has been an amazing addition to the truck! I'd say I've had it going on 2 years now ish. Today I noticed condensation in the center white light. I proceeded to unbolt the light to see what was going on. I noticed that just about ALL of the screws were not tight - the 4 mount screws and the lens screws as well. 2 of the mount plastic tabs were pulling out as well. I removed the center light, cleaned it up, wiped the o-ring and reassembled. I also put small pieces of duct tape over the plastic mounts that the 4 mount screws screw into hoping it will help them from coming dislodged. Lastly, the gasket of the light is funky as all hell, I actually cut the bottom section and put some good weather stripping I had laying around. Point of my post?</p><p></p><p>1. Periodically check the screws on your light, the 4 mount screws and the screws holding the lenses. </p><p>2. GJ should REALLY think about putting a channel around the mount and use a proper o-ring as the foamy mount doesn't age well and just gets funky. </p><p>3. I have noticed my powder coat job is pretty stained on top of the light. Not a huge deal since you can't see it unless you stand in the bed but I would expect a better PC job.</p></blockquote><p></p>
[QUOTE="nikhsub1, post: 1478573, member: 22952"] I've had my light since it the first batch that GJ made - it has been an amazing addition to the truck! I'd say I've had it going on 2 years now ish. Today I noticed condensation in the center white light. I proceeded to unbolt the light to see what was going on. I noticed that just about ALL of the screws were not tight - the 4 mount screws and the lens screws as well. 2 of the mount plastic tabs were pulling out as well. I removed the center light, cleaned it up, wiped the o-ring and reassembled. I also put small pieces of duct tape over the plastic mounts that the 4 mount screws screw into hoping it will help them from coming dislodged. Lastly, the gasket of the light is funky as all hell, I actually cut the bottom section and put some good weather stripping I had laying around. Point of my post? 1. Periodically check the screws on your light, the 4 mount screws and the screws holding the lenses. 2. GJ should REALLY think about putting a channel around the mount and use a proper o-ring as the foamy mount doesn't age well and just gets funky. 3. I have noticed my powder coat job is pretty stained on top of the light. Not a huge deal since you can't see it unless you stand in the bed but I would expect a better PC job. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
shigman
v2500hd
gt942nv00
jdm_sixtwo
Notn41
gatorbyteme
P4SHOCAT
Jmeo
sparky95
Braaaaptor
ToadSmasher2K1
cfmistry
CO_BlackRaptor
Frofan
Hambone
MarkM98
sambhutta
krunkle
silverf150
Frogger22
RRick
nemx735
Mike27t
foundations
aje0010
24NoVARaptor
willywilson
Helopilot
tabvette
krmzn
eljefe_tx
MZRaptor72
elpechedepeche
Keamg5
Speedhunter
Punkur67
RaptorMach3p5
soheilmos
WhiskeyTangoGTFO
GEN3LV
JohnyPython
Gumby
MidnightSpecial
Luchh224
jgraptor90
04Ram2500Hemi
Sozzy12
HORN HIGH ACES
mwaite09
thatJeepguy
... and 43 more.
Forum statistics
Threads
93,201
Posts
1,955,890
Members
56,484
Latest member
bjorn-dpc
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 2]
GJ Motorsports 3rd brakelight/chase light install video
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top