Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 2]
Exterior Power Panel Installed
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="jnance50" data-source="post: 1762973" data-attributes="member: 52759"><p>Lots to unpack there. The power panel is a <a href="https://www.amazon.com/dp/B0785LZQLK/?tag=fordraptorforum-20" target="_blank">generic Amazon one</a>. The <a href="https://www.amazon.com/dp/B0002UHVHI/?tag=fordraptorforum-20" target="_blank">diodes I used</a> are overkill but work well. The relay was one I just had laying around. I marked off a section of the bed where it would fit with some masking tape and cut an access panel in the bed with a mulitool. From there, I made a wiring harness by taking 5 wires and taping them together about every 12". As far as routing, it goes down the inside of the wheel well and into the adjacent frame rail, I'll try and find some photos. It pops back out just inside of the splash shield behind the drivers tire. It then runs up and over the engine compartment to the fuse/battery/upfitter wire area where it connects to the diodes/interior switch wire/and loads. There are inline fuses behind every switch in the fender well and an inline fuse on the main power wire to the panel from the battery. I can go deeper into detail on the wiring if anyone is interested.</p></blockquote><p></p>
[QUOTE="jnance50, post: 1762973, member: 52759"] Lots to unpack there. The power panel is a [URL='https://www.amazon.com/dp/B0785LZQLK/?tag=fordraptorforum-20']generic Amazon one[/URL]. The [URL='https://www.amazon.com/dp/B0002UHVHI/?tag=fordraptorforum-20']diodes I used[/URL] are overkill but work well. The relay was one I just had laying around. I marked off a section of the bed where it would fit with some masking tape and cut an access panel in the bed with a mulitool. From there, I made a wiring harness by taking 5 wires and taping them together about every 12". As far as routing, it goes down the inside of the wheel well and into the adjacent frame rail, I'll try and find some photos. It pops back out just inside of the splash shield behind the drivers tire. It then runs up and over the engine compartment to the fuse/battery/upfitter wire area where it connects to the diodes/interior switch wire/and loads. There are inline fuses behind every switch in the fender well and an inline fuse on the main power wire to the panel from the battery. I can go deeper into detail on the wiring if anyone is interested. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
elpechedepeche
Geforce
jrd79
BayouRaptor23
JohnyPython
GordoJay
kandewinn
DFS
Reptar854
Sharpie69
jAKe47
Eisner62
EMY92
VJDWashington
nikhsub1
WNCHSTR96
SCAR911
ljn21
GOTSVT?
2slo4u
ReallyNice
MurderedOutSVT
TBCTX
Madhouse
SilverGen1
WC114
MTPockets
jeanco
Jeff Oldham
downforce137
ToadSmasher2K1
MDJAK
REX111
Prormk
raptorgroyper
Jhollowell
JD05
hamster
Solidred
KAJRIP
killallblue
NATASHA
smgilles
Speedhunter
raptordawg08
So-Cal-Al-52
Justbob
Davez134
-Ryan-
BoostedToy
... and 5 more.
Forum statistics
Threads
93,192
Posts
1,955,733
Members
56,469
Latest member
ngodavid23
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 2]
Exterior Power Panel Installed
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top