Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Exterior Forum [GEN 2]
Diamondback HD and BuiltRight bed system install
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="TheRaptorIsCritical" data-source="post: 1885648" data-attributes="member: 64922"><p>Update for anyone interested in the builtright system. </p><p></p><p>It takes some planning on how you want to lay out your gear if you use the included quick fists as attaching them after mounted in bed would be….tedious. </p><p>I used the measurements for my inbound diamondback, plus a floor lay down area in the garage to check fit and clearances. I also plan to use rhino grips (3” and 1.5”) mounted with the Molle nuts from buoy right to see if they fit nicer than the risers and quick fists.</p><p></p><p>After putting the risers together and mounting them to the panels the whole bed install took about 12 minutes. I did it all in a parking lot while my dog was being groomed. The screws for the aft cleats had bed liner in the heads so I stepped down to a T27 and removed them by hand, the bell liner came off pretty easy afterwards. I used all my original brackets and hardware on top of the panels.</p><p></p><p>Shout out to built right since I am a sticker/decal hoe, every major piece had a big sticker and the risers each had a small one. Just something I like to mention about a company.</p><p></p><p>I still have 2 panels to go onto the underside of the aft DB lid when it gets here for light stuff and a hydro bladder. I’ll add an aluminum or plastic 1/2” spacer behind the panel so it’s a little easier to modify later. The forward passenger panel will hold onboard air compressor soon.</p><p></p><p>I’ll post up the rest after completion but here are the panels.</p><p>Unboxed, each side of the bed, and the passenger seat pup.</p></blockquote><p></p>
[QUOTE="TheRaptorIsCritical, post: 1885648, member: 64922"] Update for anyone interested in the builtright system. It takes some planning on how you want to lay out your gear if you use the included quick fists as attaching them after mounted in bed would be….tedious. I used the measurements for my inbound diamondback, plus a floor lay down area in the garage to check fit and clearances. I also plan to use rhino grips (3” and 1.5”) mounted with the Molle nuts from buoy right to see if they fit nicer than the risers and quick fists. After putting the risers together and mounting them to the panels the whole bed install took about 12 minutes. I did it all in a parking lot while my dog was being groomed. The screws for the aft cleats had bed liner in the heads so I stepped down to a T27 and removed them by hand, the bell liner came off pretty easy afterwards. I used all my original brackets and hardware on top of the panels. Shout out to built right since I am a sticker/decal hoe, every major piece had a big sticker and the risers each had a small one. Just something I like to mention about a company. I still have 2 panels to go onto the underside of the aft DB lid when it gets here for light stuff and a hydro bladder. I’ll add an aluminum or plastic 1/2” spacer behind the panel so it’s a little easier to modify later. The forward passenger panel will hold onboard air compressor soon. I’ll post up the rest after completion but here are the panels. Unboxed, each side of the bed, and the passenger seat pup. [/QUOTE]
Insert quotes…
Verification
Post reply
Staff online
Griffin
Administrator
Members online
shigman
PTYHRD
Matt Pearlman
alockbox
4wheelgobbler
encyphered
NJ2020
nemx735
Reaper308
Solidred
bjorn-dpc
NickyF25
debauch
JBTAC
shane310
Dan Ordoins
Raptorman19
jAKe47
pirates1456
hamster
Speedhunter
Todd Turbo S
foundations
SeasickLI
Frogger22
RaptorFun
xturdfergusonx
Otis857
Telecaster480
cr23raptor1983
Trucktreehouse
jgraptor90
Sharpie69
RockHillRaptor
Dev
Xerxes
HORN HIGH ACES
Griffin
daytona1783
FP_RPTR
Kronos2300
redsmoke
NorCal Offroad
bbarr97
Dnpbakon
MOMike
AJU1965
Wheat
jekyll537
Reptar854
... and 21 more.
Forum statistics
Threads
93,197
Posts
1,955,769
Members
56,485
Latest member
bjorn-dpc
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Exterior Forum [GEN 2]
Diamondback HD and BuiltRight bed system install
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top