Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 2]
Baja Designs S8 30" Grill Light bar kit install
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="hamster" data-source="post: 1461657" data-attributes="member: 20018"><p>Well finally finished wiring the S8, ONX6+ and BD pocket lights. I wanted wire all of them at once so I could get a clean OEM wiring look under the hood. First thing I did was extend the OEM wires using a Deutsch 6-pin Pigtail. I got the idea from this forum, but can't recall where. Here is link to where I got it. All connections were soldered and the used heat shrink tubing that has adhesive to better seal out the elements. </p><p></p><p><a href="https://www.ebay.com/itm/Deutsch-DT-6-Pin-Pigtail-Kit-14AWG-Pure-Copper-GPT-Wire-Made-in-USA/332730783268?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649" target="_blank">https://www.ebay.com/itm/Deutsch-DT-6-Pin-Pigtail-Kit-14AWG-Pure-Copper-GPT-Wire-Made-in-USA/332730783268?ssPageName=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649</a></p><p></p><p></p><p>[ATTACH=full]140316[/ATTACH] </p><p></p><p>Notice the wiring harnesses in picture above. Depending on how you route the wires, you could have a lot of excess harness for some of them. The pocket light harness was just the right length for me. So I shortened up the other two harnesses (S8 and ONX6+) and then resealed the ends. See below.</p><p></p><p>[ATTACH=full]140317[/ATTACH] </p><p>At first I had it like the following with materials I had on hand. It would have been perfectly fine to stop here.</p><p></p><p>[ATTACH=full]140318[/ATTACH] </p><p></p><p></p><p>But then I ran across this on Amazon and used it to finish it off more like OEM. Had to remove a few of the tie wraps in the above pictures before I installed it.</p><p></p><p><a href="https://www.amazon.com/gp/product/B07FW672R7/?tag=fordraptorforum-20" target="_blank">https://www.amazon.com/gp/product/B07FW672R7/?tag=fordraptorforum-20</a></p><p></p><p></p><p>[ATTACH=full]140324[/ATTACH]</p></blockquote><p></p>
[QUOTE="hamster, post: 1461657, member: 20018"] Well finally finished wiring the S8, ONX6+ and BD pocket lights. I wanted wire all of them at once so I could get a clean OEM wiring look under the hood. First thing I did was extend the OEM wires using a Deutsch 6-pin Pigtail. I got the idea from this forum, but can't recall where. Here is link to where I got it. All connections were soldered and the used heat shrink tubing that has adhesive to better seal out the elements. [URL]https://www.ebay.com/itm/Deutsch-DT-6-Pin-Pigtail-Kit-14AWG-Pure-Copper-GPT-Wire-Made-in-USA/332730783268?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649[/URL] [ATTACH=full]140316[/ATTACH] Notice the wiring harnesses in picture above. Depending on how you route the wires, you could have a lot of excess harness for some of them. The pocket light harness was just the right length for me. So I shortened up the other two harnesses (S8 and ONX6+) and then resealed the ends. See below. [ATTACH=full]140317[/ATTACH] At first I had it like the following with materials I had on hand. It would have been perfectly fine to stop here. [ATTACH=full]140318[/ATTACH] But then I ran across this on Amazon and used it to finish it off more like OEM. Had to remove a few of the tie wraps in the above pictures before I installed it. [URL]https://www.amazon.com/gp/product/B07FW672R7/?tag=fordraptorforum-20[/URL] [ATTACH=full]140324[/ATTACH] [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
KMO
Johnny@Apollo-Optics
isis
doberman
natti454
shigman
ChevyLee
Latchkey Kid
Evil Peaches
eljefe_tx
alockbox
MyBallZachErtz
NickyF25
DDD2019
Raptor farmer
SeasickLI
killallblue
Nesc204
drnash21
ToadSmasher2K1
mattl600
Sean76710
Mike27t
blazn5667
Raptorque
goblues38
albertgon1
pat247
Ifly4vamerica
schumacher1111
icecoldak
mfpf4r
ljn21
JohnyPython
TX-RAP70R
hamster
Reptar854
Slow Drive Raptor
Skmon
JTRaptor20
2slo4u
Raptor Harris
NASSTY
justinj1184
vill
kindofblue
WhiskeyTangoGTFO
Matmanand4
B boyes
Fire Ball
... and 40 more.
Forum statistics
Threads
93,193
Posts
1,955,743
Members
56,469
Latest member
ngodavid23
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 2]
Baja Designs S8 30" Grill Light bar kit install
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top