Search results

No, never found a direct fit set. Gave up on my search. Kinda forget now, but seems to me I priced what it would cost to make my own but couldn't find the correct 180°angle boot for the coil side of the wire and $$ wasn't worth the color change.

I'm looking to add a little color under the hood. I'm wanting to install new blue plug wires. What do I need to know: should I stick with the stock 8mm or increase the size, any particular brands to stay away from, is there still resistor and non-resistor wires? Ford Racing only offer wires for...

I just placed a small order with him. I believe you ya Calder.

Update: I installed a set of traction bars, and my issue ceased. Go figure!

Yes I paid $475. I considered the new leafs but figured I'd try the long bars, because its my daily driver and sees more hotrodding on the street more than off road. Oh, it'll take only minutes to take the bars off

I grenaded my transmission and driveshaft last summer due to axle wrap/wheel hop on hard acceleration off the line or at low speeds. I'm pushing 500+ rwhp and feared I was about to repeat my expensive mistake. I've been searching for different options and decided on installing a set of traction...

My fluid level is normal and I find no leakage. Steering seems to be getting worse. Figured if I take it to the dealer they'll blame it on my super charger. Sent from my SAMSUNG-SGH-I337 using Tapatalk

My dealer won't get involved because of my super charger. Sent from my SAMSUNG-SGH-I337 using Tapatalk

oops ---------- Post added at 04:20 PM ---------- Previous post was at 04:17 PM ---------- No I haven't figured it out. only does it when the outside temps are down around 20° or so. Continues to surge even when engine is at normal operating temp, but only slightly. Also, I am on my 4th...

33k, no hard off road miles Sent from my SAMSUNG-SGH-I337 using Tapatalk

Anyone having an issue with what seems as if the steering gets loose or squirrely at full throttle? (kinda hard to explain, but) I have recently noticed when I floor it at highway speeds the front end feels like it starts boating or steering gets loose, first time I noticed it is when I was...

Procharger D-1 SC. 8.5lb Boost, 62PSI Injectors. 517 HP at the rear wheels.

I know this is for exterior, but I threw in a few of my interior shots also.

I tend to smell anti freeze now and then but never found the source, bet you its from my cap. Thanks for pointing out your problem.

Where'd you get them from?

Yes a lot of wheel hop, didn't get off the go pedal quick enuff. ---------- Post added at 01:55 PM ---------- Previous post was at 01:52 PM ---------- Prolly the most aggressive I've gotten on it. My own stupidity... I was at a light between a Challenger and a Mustang... Guess I'll never...

Funny thing happened today.... What did you do with your Raptor today.... hmmm that's a good one. I broke mine. Attempted a hole shot from a stop light and didn't make it to the other side of the intersection. At first I thought I grenaded my drive shaft. Towed it home, had to replace entire...

They are on the 2017's

Check out : Raptor Embroidery aka Raptor_Al_41 He does quite a few different things for your truck.

That explains it.... cheap.... I did an ebay special to my interior and reverse lights. Noticed the dome LED dim glow all times. I just replaced my reverse LEDs again due to the ebay specials wasn't bright enuff and discovered they were begining to melt the pig tail housing, glad I found and...

Driver and pass both have this hump for the under seat heat/AC vent. W/O including this info while ordering it creates this small gap (actually it's insignificant but may as well have them fit properly)

when ordering, remember to input all info regarding your truck, I mistakenly didn't include that I have under the seat vents and my liners don't form snuggly around the shape in the floor under the front of the seat, which is only a minor detail, but if I had to do it over again I'd surely...

You can for $249 from Ford for the kit

I did them myself, but I have recently sold all my equipment and got out of the business.

The acrylic would be a much cleaner look, the silicone is troublesome not to make a mess.