Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford F-150 Raptor General Discussions [GEN 2]
What did you do to your Raptor today? (Gen2)
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="MZRaptor72" data-source="post: 1369451" data-attributes="member: 31407"><p>Thanks! As for your question... Well... i guess not... but i did. I did one side before i noticed there are areas drilled out right where they will end up. Everyone talks about the groove cut into the stock bead locks. Mine stuck out too far for the groove and that is what i was fixated on. The holes are bored out for balancing and vary in depth but are located right where you need them. See below:</p><p></p><p>[ATTACH=full]293111[/ATTACH]</p><p></p><p>[ATTACH=full]293112[/ATTACH]</p><p></p><p>[ATTACH=full]293113[/ATTACH]</p><p></p><p>So long as yours were balanced the same way... i think you are fine to save yourself the extra work. On the other hand.... if you ever go with something different you’ll have to deal with it. I just did both sides in back so i don’t have to worry about it.</p><p></p><p>Couple of notes... i wire brushed everything real good. Used high temp anti-seize between spacer and hub, used red loctite to attach, and also sealed up my cut ends where i ground studs.</p><p></p><p></p><p>Sent from my iPhone using Tapatalk</p></blockquote><p></p>
[QUOTE="MZRaptor72, post: 1369451, member: 31407"] Thanks! As for your question... Well... i guess not... but i did. I did one side before i noticed there are areas drilled out right where they will end up. Everyone talks about the groove cut into the stock bead locks. Mine stuck out too far for the groove and that is what i was fixated on. The holes are bored out for balancing and vary in depth but are located right where you need them. See below: [ATTACH=full]293111[/ATTACH] [ATTACH=full]293112[/ATTACH] [ATTACH=full]293113[/ATTACH] So long as yours were balanced the same way... i think you are fine to save yourself the extra work. On the other hand.... if you ever go with something different you’ll have to deal with it. I just did both sides in back so i don’t have to worry about it. Couple of notes... i wire brushed everything real good. Used high temp anti-seize between spacer and hub, used red loctite to attach, and also sealed up my cut ends where i ground studs. Sent from my iPhone using Tapatalk [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
BadWRP
TAC71
kevo_lo
tonythis
Psirus7
bellnghmrider
OBXRAPTOR17
Shane361
Frogger22
catinthehat85
weldoid
CleverGirl_
Beinkounter
GCATX
pattmarsons
17baker
wesleywest
tcm glx
rohokieop
jekyll537
Rahptor
kocher93
nicewaptor
RobSpring661
Lupuswins
WhiskeyTangoGTFO
BBLV
Whoops
Drkknght
XSTNKT
Domin0
RCorsa
Old-Raptor-guy
Butterz
taquitos
LibertyDNP
SB88
az_gen3
WTX
NJ2020
cuts
The Doo
Raptor_arw
karna
jhgrossi2004
Brody Goble
2011_Shelby
2024RaptorR_NOVA
DaveInMn
cheese
... and 10 more.
Forum statistics
Threads
93,189
Posts
1,955,679
Members
56,469
Latest member
ngodavid23
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford F-150 Raptor General Discussions [GEN 2]
What did you do to your Raptor today? (Gen2)
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top