Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Exterior Modifications Forum [GEN 1]
PowerScope/Max Tow Mirrors Installed
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="blackraptor99" data-source="post: 691878" data-attributes="member: 6237"><p>I installed diodes initially so the marker light would be dimmer than when blinking but then the marker wasn't bright enough compared to the other marker lights. In the end I just made the Recon LED a marker light and didn't bother with having it blink when signalling. There's no need to have it blink to be honest.</p><p></p><p>There are a lot of wires going into the back of that big connector and it's covered up with sheathing. Rather than trying to figure out which one might have park light power I just found the right wire to tap into beside the drivers seat sill cover, spliced in and ran it as noted above. You only need to run one wire (pick up ground in mirror) so only a very small hole needed to be drilled through the back of the connector so you can't see it. Even if you were able to find the wire in the connector I believe you'd have to put a pin in the door side as they're all blank. I searched the other F150 forums for a better solution but this was the best I could find.</p></blockquote><p></p>
[QUOTE="blackraptor99, post: 691878, member: 6237"] I installed diodes initially so the marker light would be dimmer than when blinking but then the marker wasn't bright enough compared to the other marker lights. In the end I just made the Recon LED a marker light and didn't bother with having it blink when signalling. There's no need to have it blink to be honest. There are a lot of wires going into the back of that big connector and it's covered up with sheathing. Rather than trying to figure out which one might have park light power I just found the right wire to tap into beside the drivers seat sill cover, spliced in and ran it as noted above. You only need to run one wire (pick up ground in mirror) so only a very small hole needed to be drilled through the back of the connector so you can't see it. Even if you were able to find the wire in the connector I believe you'd have to put a pin in the door side as they're all blank. I searched the other F150 forums for a better solution but this was the best I could find. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
BoostCreep
Chewie
PlainsRaptor
ricetuna
mlax
smteal
Astro94
taquitos
KMO
tractorpole
wyomingraptor
timgoldstein7
MrMicky
Al Terp
1BAD454SSv2
Rednose
elpechedepeche
nickspins
Foozer
icecoldak
Jsousa03
Jhollowell
MetalDaze
Pyro3601
elking
azwldcat13
3Dog
2012SCSVT
Ilushikmdo
Forum statistics
Threads
93,487
Posts
1,962,279
Members
56,774
Latest member
colinmg
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Exterior Modifications Forum [GEN 1]
PowerScope/Max Tow Mirrors Installed
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top