Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Exhaust and Cutouts Discussion [GEN 1]
Need ideas for broken header bolts
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Ratpatator" data-source="post: 1453281" data-attributes="member: 20527"><p>So I need a little advice on how to get the broken header bolts out of the block. Wondering if someone has had experience with this issue. If there is a thread about this already please point me in the right direction.</p><p></p><p>It's the two studs that are on the back exhaust port on the passenger side (so far). I believe they are flush or a little recessed into the block. Am I going to have to pull the engine to get to them or is there enough room to rotate the engine in the truck with engine mounts removed. I have ****** long tubes to go back in and I'm worried that more studs will break during removal. I also don't have a shop to use right now so this will probably end up being done in the damn driveway. Any tricks or ideas would be much appreciated.</p></blockquote><p></p>
[QUOTE="Ratpatator, post: 1453281, member: 20527"] So I need a little advice on how to get the broken header bolts out of the block. Wondering if someone has had experience with this issue. If there is a thread about this already please point me in the right direction. It's the two studs that are on the back exhaust port on the passenger side (so far). I believe they are flush or a little recessed into the block. Am I going to have to pull the engine to get to them or is there enough room to rotate the engine in the truck with engine mounts removed. I have ****** long tubes to go back in and I'm worried that more studs will break during removal. I also don't have a shop to use right now so this will probably end up being done in the damn driveway. Any tricks or ideas would be much appreciated. [/QUOTE]
Insert quotes…
Verification
Post reply
Staff online
Griffin
Administrator
Members online
cfmistry
GenDos19
Bubba0612
RaptorFun
Dev
vill
Badboy4fun_wa
someday
Chupacabras
Azurebeast
Pyro3601
pjbrennan
brunorulez
HuffRanch
gatorbyteme
Russ103
debauch
Todd Turbo S
Evil Peaches
Griffin
Jmeo
Locker1
Nantucketdink
Latchkey Kid
schumacher1111
mgbond12
Xerxes
brady18363
US HWY 666
yoxxi
HORN HIGH ACES
DMacDonald
Goose8651
eljefe_tx
JBTAC
hamster
Notn41
jayspick
dillard09
HeyItsARaptor
Frogger22
richardusmc
MotoDad
FP_RPTR
goblues38
Teledatgeek
Rekkr
IDI-Charlie
SeasickLI
BLEEKER
... and 16 more.
Forum statistics
Threads
93,197
Posts
1,955,787
Members
56,485
Latest member
bjorn-dpc
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Exhaust and Cutouts Discussion [GEN 1]
Need ideas for broken header bolts
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top