Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Engine Discussion and Performance Mods
MagnaFlow D-Fit Muffler (#19465)
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="TRMFAM" data-source="post: 1482336" data-attributes="member: 39887"><p>I am using an iPhone 11 Pro with Decibel Pro app and Niosh app with microphone pointed at the trailer hitch opening about waist high 10' from rear of truck centered...</p><p></p><p><strong><u>Cold Start</u></strong>:</p><p>STOCK: Pro Decibel app Cold start outside 82.7 Max and 77.6 Avg</p><p>MF: Pro Decibel app Cold start outside 90.6 Max and 87.7 Avg</p><p></p><p>STOCK: Niosh app Cold start outside 70</p><p>MF: Niosh app Cold start outside <u>72</u></p><p></p><p><u><strong>Idling:</strong></u></p><p>STOCK: Pro Decibel app Idling after start is 72.3 DB Avg</p><p>MF: Pro Decibel app Idling after start is 86.7 DB Avg</p><p></p><p>STOCK: Niosh app Idling after start is 60-62</p><p>MF: Niosh app Idling after start is 62-63</p><p></p><p><strong><u>Driving </u></strong>- Holding the phone approximately chest level with mic pointed at chest in Normal driving mode with factory exhaust sound ON:</p><p>STOCK: Pro Decibel app 15-70 MPH WFO is 96.1 Max and 89.9 Avg</p><p>STOCK: Pro Decibel app 70 MPH cruising is 84.4 Avg</p><p>MF: Pro Decibel app 15-70 MPH WFO is <u>Pending</u> Max and Pending Avg</p><p>MF: Pro Decibel app 70 MPH cruising is <u>Pending</u> Avg</p><p></p><p>Clearly my phone / Pro Decibel app is hypersensitive and reads high DB...no way just riding in the truck at 70 MPH = a Lawn mower!</p><p></p><p><strong><u>Install</u></strong> - Install was fairly straightforward, first throw away the instructions as it appears they were copied from the cat-back system and has you remove the resonator, this is not needed. Also verify you received the correct clamps as one of mine was for a 2.75" exhaust vs. 3" required. Install time approx. 1 hour.</p><p></p><p>Here is what I did YMMV</p><p>Step 1: 10mm socket remove 2 nuts per side (4 total) that hold the tail pipe hanger at the bumper.</p><p>Step 2: 10mm socket remove the 2 bolts per side (4 total) on the exhaust pipe hanger (between muffler and outlet hanger.</p><p>Step 3: 15mm socket loosen the clamp for each tail pipe at the connection with the muffler (2 total) and lower tail pipes.</p><p>Step 4: 15mm socket loosen the muffler inlet clamps between the resonator and muffler (3 total).</p><p>Step 5: 10mm socket remove the front and rear muffler hangers (3 bolts total) and remove the stock muffler.</p><p>Step 6: transfer stock muffler hangers to MF muffler, slide on clamps for tail pipes and reinstall 2 bolt clamp to the pipe from the resonator (you have to bend a tab on the stock muffler to remove).</p><p>Step 7: line up muffler, insert into stock pipe from resonator and re-install hangers finger tight.</p><p>Step 8: line up drivers side exhaust, insert into MF muffler and reinstall mid pipe hanger, reinstall rear hanger finger tight.</p><p>Step 9: repeat step 8 for passenger side.</p><p>Step 10: starting at the furthest point forward tighten pipe clamps (muffler inlet from res), then muffler hangers, tail pipe / muffler joint, mid hangers and finally line up tail pipes to be even and sit at the appropriate distance from the bumper.</p><p>Step 11: Start up and smile!</p><p></p><p>I have installed several aftermarket exhausts across various vehicles and have found it easier to remove the entire hanger vs lining up the studs to rubber...I will give MF credit the studs for the rubber isolators are right on.</p></blockquote><p></p>
[QUOTE="TRMFAM, post: 1482336, member: 39887"] I am using an iPhone 11 Pro with Decibel Pro app and Niosh app with microphone pointed at the trailer hitch opening about waist high 10' from rear of truck centered... [B][U]Cold Start[/U][/B]: STOCK: Pro Decibel app Cold start outside 82.7 Max and 77.6 Avg MF: Pro Decibel app Cold start outside 90.6 Max and 87.7 Avg STOCK: Niosh app Cold start outside 70 MF: Niosh app Cold start outside [U]72[/U] [U][B]Idling:[/B][/U] STOCK: Pro Decibel app Idling after start is 72.3 DB Avg MF: Pro Decibel app Idling after start is 86.7 DB Avg STOCK: Niosh app Idling after start is 60-62 MF: Niosh app Idling after start is 62-63 [B][U]Driving [/U][/B]- Holding the phone approximately chest level with mic pointed at chest in Normal driving mode with factory exhaust sound ON: STOCK: Pro Decibel app 15-70 MPH WFO is 96.1 Max and 89.9 Avg STOCK: Pro Decibel app 70 MPH cruising is 84.4 Avg MF: Pro Decibel app 15-70 MPH WFO is [U]Pending[/U] Max and Pending Avg MF: Pro Decibel app 70 MPH cruising is [U]Pending[/U] Avg Clearly my phone / Pro Decibel app is hypersensitive and reads high DB...no way just riding in the truck at 70 MPH = a Lawn mower! [B][U]Install[/U][/B] - Install was fairly straightforward, first throw away the instructions as it appears they were copied from the cat-back system and has you remove the resonator, this is not needed. Also verify you received the correct clamps as one of mine was for a 2.75" exhaust vs. 3" required. Install time approx. 1 hour. Here is what I did YMMV Step 1: 10mm socket remove 2 nuts per side (4 total) that hold the tail pipe hanger at the bumper. Step 2: 10mm socket remove the 2 bolts per side (4 total) on the exhaust pipe hanger (between muffler and outlet hanger. Step 3: 15mm socket loosen the clamp for each tail pipe at the connection with the muffler (2 total) and lower tail pipes. Step 4: 15mm socket loosen the muffler inlet clamps between the resonator and muffler (3 total). Step 5: 10mm socket remove the front and rear muffler hangers (3 bolts total) and remove the stock muffler. Step 6: transfer stock muffler hangers to MF muffler, slide on clamps for tail pipes and reinstall 2 bolt clamp to the pipe from the resonator (you have to bend a tab on the stock muffler to remove). Step 7: line up muffler, insert into stock pipe from resonator and re-install hangers finger tight. Step 8: line up drivers side exhaust, insert into MF muffler and reinstall mid pipe hanger, reinstall rear hanger finger tight. Step 9: repeat step 8 for passenger side. Step 10: starting at the furthest point forward tighten pipe clamps (muffler inlet from res), then muffler hangers, tail pipe / muffler joint, mid hangers and finally line up tail pipes to be even and sit at the appropriate distance from the bumper. Step 11: Start up and smile! I have installed several aftermarket exhausts across various vehicles and have found it easier to remove the entire hanger vs lining up the studs to rubber...I will give MF credit the studs for the rubber isolators are right on. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
CT808
Colorapdo
Rucku5
Littlefx4
soudaldayoli
wyomingraptor
Danny_Apolos
jonw5300
bellnghmrider
Stroked out
Sweet-Ride
Turning Blue
FoxNotch
Raptor_NV
Gator85
nelsonr103
Forum statistics
Threads
93,278
Posts
1,957,787
Members
56,567
Latest member
erikn
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Engine Discussion and Performance Mods
MagnaFlow D-Fit Muffler (#19465)
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top