Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 3 (2021+) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 3]
Installed - Fog, Driving/Combo, Spot lights - Baja Designs Squadron Pro
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="maxr" data-source="post: 1749885" data-attributes="member: 54967"><p>Bought a set of Baja Design Squadron Pro - Wide Cornering-Amber, Driving/Combo, Spot along with mounting brackets, wiring harness and AUX1/Fog relocation harness from [USER=24406]@Specialtyperformanceparts[/USER].</p><p></p><p>Wide Cornering to AUX1</p><p>Driving Combo to AUX2</p><p>Spot to AUX 3</p><p></p><p>That is how I installed the lights in the mounting bracket from the outside to inside. The AUX1 is much easier for me to use then reaching down and pressing the FOG switch.</p><p></p><p>TIP - I flipped the base plates AND the lens covers so the BD logo, etc. were orientated UP</p><p>TIP - install the BD lights with the correct orientation of the mounting brackets. (see 3rd pic) yeah @*#$ did it wrong initially. caught it when I test fit the mounted lights and discovered the lights were recessed too much.</p><p>TIP - Remove the front tire(s). I was too stubborn and it added a lot of time having to remove the bolts with a socket wrench barely able to get my arms in place.</p><p>TIP - Once the factory fog lights are removed, I threaded rebar tie wire from the driver side to the passenger side where a couple other wiring looms were run (just behind the grill). I tapped up the connectors with gaffer tape and was able to easily pull them to the driver side.</p><p>TIP - I angled the mounting bracket during installation so the top of the BD light housings were as close to the top of the opening as possible. My install had the outside bracket mounted slighly higher then the inside. It is an easy adjustment to fiddle with since the bracket has adjustment grooves for each bolt.</p><p></p><p>The brace uses a 8mm, the lower bolts and 2 of the upper bolts are 10mm. There are 2 T-30 on the top that hold the light assembly. These are a PITA to remove and one of mine was stripped. The mounting bracket only requires 4 bolts plus re-attaching the brace so I tossed the T-30s.</p><p></p><p>Think they look great. Plan to get some black weatherproof tape to wrap the connectors so they can't be seen when looking down into the space just in front of the lights. Will test performance tomorrow night. </p><p></p><p>John [USER=24406]@Specialtyperformanceparts[/USER] was available to answer a couple question via phone. Great support from him</p><p></p><p></p><p>[ATTACH=full]344031[/ATTACH]</p><p></p><p></p><p>[ATTACH=full]344032[/ATTACH]</p><p></p><p>[ATTACH=full]344033[/ATTACH]</p></blockquote><p></p>
[QUOTE="maxr, post: 1749885, member: 54967"] Bought a set of Baja Design Squadron Pro - Wide Cornering-Amber, Driving/Combo, Spot along with mounting brackets, wiring harness and AUX1/Fog relocation harness from [USER=24406]@Specialtyperformanceparts[/USER]. Wide Cornering to AUX1 Driving Combo to AUX2 Spot to AUX 3 That is how I installed the lights in the mounting bracket from the outside to inside. The AUX1 is much easier for me to use then reaching down and pressing the FOG switch. TIP - I flipped the base plates AND the lens covers so the BD logo, etc. were orientated UP TIP - install the BD lights with the correct orientation of the mounting brackets. (see 3rd pic) yeah @*#$ did it wrong initially. caught it when I test fit the mounted lights and discovered the lights were recessed too much. TIP - Remove the front tire(s). I was too stubborn and it added a lot of time having to remove the bolts with a socket wrench barely able to get my arms in place. TIP - Once the factory fog lights are removed, I threaded rebar tie wire from the driver side to the passenger side where a couple other wiring looms were run (just behind the grill). I tapped up the connectors with gaffer tape and was able to easily pull them to the driver side. TIP - I angled the mounting bracket during installation so the top of the BD light housings were as close to the top of the opening as possible. My install had the outside bracket mounted slighly higher then the inside. It is an easy adjustment to fiddle with since the bracket has adjustment grooves for each bolt. The brace uses a 8mm, the lower bolts and 2 of the upper bolts are 10mm. There are 2 T-30 on the top that hold the light assembly. These are a PITA to remove and one of mine was stripped. The mounting bracket only requires 4 bolts plus re-attaching the brace so I tossed the T-30s. Think they look great. Plan to get some black weatherproof tape to wrap the connectors so they can't be seen when looking down into the space just in front of the lights. Will test performance tomorrow night. John [USER=24406]@Specialtyperformanceparts[/USER] was available to answer a couple question via phone. Great support from him [ATTACH type="full"]344031[/ATTACH] [ATTACH type="full"]344032[/ATTACH] [ATTACH type="full"]344033[/ATTACH] [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
Coyote_695
Hambone
thatJeepguy
k3k0a808
Lupuswins
Comish
Jordan Bocko
HighSpeedLowDrag
icecoldak
FoxNotch
Hard R
reesbridges
HighNoon
Qs Raptor
vill
Tyler Gibson
sct
Harry P Ness
GreenGoblin
nikhsub1
ChuckPeazy
scroper
scpete24
Solidred
hyrepower
BoostCreep
New recaros
jm77
e10tran
VJDWashington
KX250R
donttellmywiferacing
bilegt
Badboy4fun_wa
encyphered
jcollier_91
silvertige
Whoops
ATG
ln13ln13
stevot
RiskTkr
Keith88
Punkur67
Forum statistics
Threads
93,171
Posts
1,955,300
Members
56,440
Latest member
jumpcutter
Forums
GEN 3 (2021+) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 3]
Installed - Fog, Driving/Combo, Spot lights - Baja Designs Squadron Pro
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top