Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Audio/Video/Electronics Forum [GEN 2]
All this audio talk but no forscan info
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="jakeO" data-source="post: 1172892" data-attributes="member: 4904"><p>This is info from Dan's link <a href="http://www.2gfusions.net/showthread.php?tid=3704" target="_blank">Variable Line Level Preamp Outputs From ACM (Factory Radio) For Amplifier Upgrades</a></p><p></p><p>NAV IS RETAINED </p><p></p><p></p><p>These are on the Sony DSP Harness (Twisted Pair CAT5, should be easy to spot):</p><p> Front Left: Yellow (+), Blue (-) (Sony DSP: 7, 17)</p><p> Front Right: Violet (+), Brown/Yellow (-) (Sony DSP: 9, 19)</p><p> Rear Left: Orange (+), White (-) (Sony DSP: 2, 12)</p><p> Rear Right: Green (+), Gray (-) (Sony DSP: 4, 14)</p><p></p><p> Amp Remote Turn On: Red (Sony DSP - Pin 3) </p><p> Note: this remote turn on wire is NOT 12 volts (approx 6 volts)... some amplifiers may require a 12 volt input and may need to convert this output with a third party device. Some sound processors, such as the JBL MS-8, support 4 Volts and higher as a remote turn on voltage so this is not an issue.</p><p></p><p>UPDATE:</p><p> Better remote turn on wire for Push to Start Vehicles:</p><p> Connector C3501 - Pin 5 - Brown/Yellow (22 Gauge) - 12 Volt w/ Delayed Accessory Feature</p><p> - This wire is going into the 150 Watt AC/DC Power Inverter</p><p></p><p></p><p>For Vehicles With Factory Sony DSP/Amplifier Only:</p><p></p><p>Needed Wiring Terminal Inserts: Order from FordParts.com, local dealer, etc...</p><p> Part Number: DU2Z-14474-CA</p><p></p><p>I added and soldered two wires to the ACM and APIM Harnesses... These two mono out wires are required if you are disconnecting the Sony Amplifier, previously in use, to use your own amplifiers to the speakers/subwoofer without a Line Output Converter. These two wires reroute the Sync Voice from the APIM, back into the ACM, and out your aftermarket speakers. </p><p></p><p>Without adding these two wires, there will be no voice on navigation directions and voice commands will not have any feedback to confirm prompts. </p><p></p><p>It is accomplished by adding two wire terminals to the ACM Harness (Pins 8,21) and soldering them to the Sync wires on the APIM Harness (Pins 3,4).<span style="color: Red"></span></p><p><span style="color: Red"></span></p><p><span style="color: Red"><span style="font-size: 9px">---------- Post added at 11:39 PM ---------- Previous post was at 11:34 PM ----------</span></span></p><p><span style="color: Red"></span></p><p><span style="color: Red"></span></p><p></p><p>You could not do a after market. you would lose too much control of the truck. I have had plenty of people with brand new Kenwoods / alpine. and they all said they wish their HU worked as nice as mine.</p></blockquote><p></p>
[QUOTE="jakeO, post: 1172892, member: 4904"] This is info from Dan's link [url=http://www.2gfusions.net/showthread.php?tid=3704]Variable Line Level Preamp Outputs From ACM (Factory Radio) For Amplifier Upgrades[/url] NAV IS RETAINED These are on the Sony DSP Harness (Twisted Pair CAT5, should be easy to spot): Front Left: Yellow (+), Blue (-) (Sony DSP: 7, 17) Front Right: Violet (+), Brown/Yellow (-) (Sony DSP: 9, 19) Rear Left: Orange (+), White (-) (Sony DSP: 2, 12) Rear Right: Green (+), Gray (-) (Sony DSP: 4, 14) Amp Remote Turn On: Red (Sony DSP - Pin 3) Note: this remote turn on wire is NOT 12 volts (approx 6 volts)... some amplifiers may require a 12 volt input and may need to convert this output with a third party device. Some sound processors, such as the JBL MS-8, support 4 Volts and higher as a remote turn on voltage so this is not an issue. UPDATE: Better remote turn on wire for Push to Start Vehicles: Connector C3501 - Pin 5 - Brown/Yellow (22 Gauge) - 12 Volt w/ Delayed Accessory Feature - This wire is going into the 150 Watt AC/DC Power Inverter For Vehicles With Factory Sony DSP/Amplifier Only: Needed Wiring Terminal Inserts: Order from FordParts.com, local dealer, etc... Part Number: DU2Z-14474-CA I added and soldered two wires to the ACM and APIM Harnesses... These two mono out wires are required if you are disconnecting the Sony Amplifier, previously in use, to use your own amplifiers to the speakers/subwoofer without a Line Output Converter. These two wires reroute the Sync Voice from the APIM, back into the ACM, and out your aftermarket speakers. Without adding these two wires, there will be no voice on navigation directions and voice commands will not have any feedback to confirm prompts. It is accomplished by adding two wire terminals to the ACM Harness (Pins 8,21) and soldering them to the Sync wires on the APIM Harness (Pins 3,4).[COLOR="Red"] [SIZE=1]---------- Post added at 11:39 PM ---------- Previous post was at 11:34 PM ----------[/SIZE] [/COLOR] You could not do a after market. you would lose too much control of the truck. I have had plenty of people with brand new Kenwoods / alpine. and they all said they wish their HU worked as nice as mine. [/QUOTE]
Insert quotes…
Verification
Post reply
Staff online
Griffin
Administrator
Members online
xturdfergusonx
Mark Cormier
Whoops
JDMCTR00
Toadster
someday
elpechedepeche
icecoldak
Venti Raptor
Keystone
RUFdriver
GCATX
peeweeman250
Brad12
BBLV
rhythmchamber
rp2024
Punkur67
RamseyF
damaschke
jdm_sixtwo
khunter
brink
thirstyforgas
Raptor1776
ReddingRaptor
encyphered
shigman
raptordawg08
topher1130
drjung77
Yc_Raptor
akbjr
2012SCSVT
olverac
bobbyph1
MIK3
CruiserClass
TomDirt
mtesni
SurfRaptor
24NoVARaptor
Stonehide
HeyItsARaptor
Griffin
Forum statistics
Threads
93,349
Posts
1,959,402
Members
56,636
Latest member
RAPTORHD
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Audio/Video/Electronics Forum [GEN 2]
All this audio talk but no forscan info
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top