Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Interior Modifications Forum [GEN 1]
Aftermarket gauge question, aeroforce interceptor
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="sln157" data-source="post: 1362282" data-attributes="member: 22001"><p>Let me pull it up and give it a look to make sure I’m not crazy, it was last May since I did my install. I’ll get back with you.</p><p></p><p>Edit: I stand corrected, you were right on the orange wire & add-a-circuit in the photo (was for the pump). Forgot I’d ordered the add-a-circuit but didn’t need it since I used the 5v adapter. I’ve since remounted the map sensor and sheathed the wire loom at the firewall closer to the grommet where the wires ran through for the gauge. I’d of rather tapped into a source like bsimms89 as I’ve already had one 5v regulator go bad. As for the vacuum/boost port, it’s a 1/8” NPT I ordered from summit with neoprene tubing. I did use the butt connector provided to tap in as well. Some of the instructions were somewhat vague and when I ordered my kit last March I was one of the few to get the Gen3 at the time. By the time I received mine in May and installed it, I’d had it on for less than a week and it seized (rotors shredded), it was replaced free of charge due to a freak assembly issue before it was shipped I was told. I’d already installed billet OPG’s prior to the blower but had a panic attack I’d lost oil pressure as the belt was tight enough when it seized that the motor wouldn’t crank. After the replacement unit and JDM tune it’s been all smiles and no issues for a year now. Mike Malicoat from Whipple was a huge help during the install process with answering my questions. I ordered the stage2 kit and along with new and updated parts, the manual supplied was outdated.</p></blockquote><p></p>
[QUOTE="sln157, post: 1362282, member: 22001"] Let me pull it up and give it a look to make sure I’m not crazy, it was last May since I did my install. I’ll get back with you. Edit: I stand corrected, you were right on the orange wire & add-a-circuit in the photo (was for the pump). Forgot I’d ordered the add-a-circuit but didn’t need it since I used the 5v adapter. I’ve since remounted the map sensor and sheathed the wire loom at the firewall closer to the grommet where the wires ran through for the gauge. I’d of rather tapped into a source like bsimms89 as I’ve already had one 5v regulator go bad. As for the vacuum/boost port, it’s a 1/8” NPT I ordered from summit with neoprene tubing. I did use the butt connector provided to tap in as well. Some of the instructions were somewhat vague and when I ordered my kit last March I was one of the few to get the Gen3 at the time. By the time I received mine in May and installed it, I’d had it on for less than a week and it seized (rotors shredded), it was replaced free of charge due to a freak assembly issue before it was shipped I was told. I’d already installed billet OPG’s prior to the blower but had a panic attack I’d lost oil pressure as the belt was tight enough when it seized that the motor wouldn’t crank. After the replacement unit and JDM tune it’s been all smiles and no issues for a year now. Mike Malicoat from Whipple was a huge help during the install process with answering my questions. I ordered the stage2 kit and along with new and updated parts, the manual supplied was outdated. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
nemx735
Punkur67
krmzn
elpechedepeche
RaptorMach3p5
Speedhunter
Frofan
MZRaptor72
willywilson
eljefe_tx
krunkle
P4SHOCAT
gt942nv00
soheilmos
WhiskeyTangoGTFO
GEN3LV
Keamg5
24NoVARaptor
JohnyPython
Hambone
v2500hd
foundations
Gumby
MidnightSpecial
Luchh224
shigman
cfmistry
jgraptor90
gatorbyteme
04Ram2500Hemi
Sozzy12
HORN HIGH ACES
mwaite09
thatJeepguy
Goose8651
GCATX
Frogger22
pat247
sambhutta
kshipp
jp1seattle
bobriley59
mattwrapps
Sorry About Da Noise
Ryan Voight
Otis857
Utexmed
Bozz
NorCal Offroad
jbbaker5196
... and 42 more.
Forum statistics
Threads
93,201
Posts
1,955,886
Members
56,484
Latest member
bjorn-dpc
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Interior Modifications Forum [GEN 1]
Aftermarket gauge question, aeroforce interceptor
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top