Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 2]
Wiring for bed bar lights with tonneau cover
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="dbalt" data-source="post: 1873510" data-attributes="member: 58399"><p>I want to run wires from these mounted light pods into the bed. I have a power source I can tap into inside the bed where I already have my compressor installed. I was thinking about running the wire harness along the bed bar down the side bracket and through the t-slot channel on my retrax cover either at the tailgate or forward to the front of the bar where I can access it through the drain holes.</p><p></p><p>I was wondering if anyone had any suggestions for a better method to handle wiring these up. I'm not opposed to drilling a hole with a grommet but I'm not sure there's really a feasible area to do that and I'd prefer not to drill into the bed or bed cover if there's an alternative.</p><p></p><p>If I can't find a clean solution for this, I'll probably relocate these to the rear bumper.</p><p></p><p>[ATTACH=full]391677[/ATTACH]</p></blockquote><p></p>
[QUOTE="dbalt, post: 1873510, member: 58399"] I want to run wires from these mounted light pods into the bed. I have a power source I can tap into inside the bed where I already have my compressor installed. I was thinking about running the wire harness along the bed bar down the side bracket and through the t-slot channel on my retrax cover either at the tailgate or forward to the front of the bar where I can access it through the drain holes. I was wondering if anyone had any suggestions for a better method to handle wiring these up. I'm not opposed to drilling a hole with a grommet but I'm not sure there's really a feasible area to do that and I'd prefer not to drill into the bed or bed cover if there's an alternative. If I can't find a clean solution for this, I'll probably relocate these to the rear bumper. [ATTACH type="full" width="439px"]391677[/ATTACH] [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
riv
jtschratz
WH7
Aboshi
Syberspace
RRick
WC114
JMH2019FPB
Morgan
TheButcher
JAYL1985
Raptor812
Brocephusmax
HighwaySentinel
KingKoopa17
Dan H
Marlboroman
Winchester30
pirates1456
ljn21
RaptorAU
MarkOne
mobob
AJ36_LeadFootG3
tk3
Admin.RealTruck
PlainsRaptor
never_summer
shank_guru
Space Ghost
SSWIM
RHCLLC
jAKe47
pat247
isis
soccerUber
kylesatx
jdm_sixtwo
Latchkey Kid
BBR
Slaptor911
2011_Shelby
wheelman55
ineedaBubble
03Cobraraptor
ToadSmasher2K1
Josfue
Rptrlyfe
MEIRONMAN207
GordoJay
... and 10 more.
Forum statistics
Threads
93,093
Posts
1,953,106
Members
56,355
Latest member
txcoach
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Lighting Forum [GEN 2]
Wiring for bed bar lights with tonneau cover
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top