SilentShooter
FRF Addict
Shop is doing it. Condo does not let me work on the truck so no place to do it myself..
What did u do to your raptor today?
- Thread starter CAbimmer
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
03svt
Full Access Member
Put my S&B filter and fender inlet in
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
J. Wolfe
FRF Addict
mitcha
Member
Smoked the 3rd brake light. Matches the rest a little bit better now.
Sent from my SM-G925V using Tapatalk
t_j
FRF Addict
* Painted the new tablet mount
* Installed a relay panel and fuse block on the back of the glove box to relocate relays from under the hood that kept getting wet and going wrong
* Switched up some wiring
- Moved winch controller power from switch panel to aux 1
- Moved phone/gps chargers from aux 3 to aux 2 leaving only the switch panel power on aux 3
- Moved the stop tail turn controller power from the switch panel to aux 4
- Moved front cubes from aux 4 to switch panel with in cab relay
- Moved front 40" from aux 2 to switch panel with in cab relay
- The result - all AUX lighting is now on the switch panel and can be controlled with a master on/off switch on aux3 while remaining individually controllable
* Ran power lines for the inverter that @Kmandoske gave me so I can charge camera and drone batteries on the go
Relay/fuse panel:
Rats nest:
This is what happens when you run 12 cables to the bed distribution box and 12 to under the hood.
* Installed a relay panel and fuse block on the back of the glove box to relocate relays from under the hood that kept getting wet and going wrong
* Switched up some wiring
- Moved winch controller power from switch panel to aux 1
- Moved phone/gps chargers from aux 3 to aux 2 leaving only the switch panel power on aux 3
- Moved the stop tail turn controller power from the switch panel to aux 4
- Moved front cubes from aux 4 to switch panel with in cab relay
- Moved front 40" from aux 2 to switch panel with in cab relay
- The result - all AUX lighting is now on the switch panel and can be controlled with a master on/off switch on aux3 while remaining individually controllable
* Ran power lines for the inverter that @Kmandoske gave me so I can charge camera and drone batteries on the go
Relay/fuse panel:
Rats nest:
This is what happens when you run 12 cables to the bed distribution box and 12 to under the hood.
jdruzik
FRF Addict
Ok, here are a couple of images ...
Blue vinyl accent under side vents...
They match my hood emblems...
Last edited:
t_j
FRF Addict
Duplicate post
Last edited:
jdruzik
FRF Addict
^That's just crazy...
Sano Dano
Full Access Member
Changed out 2 of 3 blend door activators, the drivers side is working so didn't have to remove the complete dash as in the video that @CoronaRaptor posted, only had to remove the center console and radio to access the blend door that controls the passenger side, see video posted by @Droid, the third blend door is accessible from under the steering wheel.
First pic is upside down.....next to the steering wheel
Close up of the blend motor......had to shorten my 5/16 socket to get the back screw
Third pic is of the door behind the radio.
Close up of the blend motor behind the radio.....with blend motor removed
Overall was fairly simple to do......beats $700-$800 at Ford!
First pic is upside down.....next to the steering wheel
Close up of the blend motor......had to shorten my 5/16 socket to get the back screw
Third pic is of the door behind the radio.
Close up of the blend motor behind the radio.....with blend motor removed
Overall was fairly simple to do......beats $700-$800 at Ford!
Attachments
Similar threads
