Geisers may have ruined my shocks!

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

dsiggi

Full Access Member
Joined
Mar 27, 2025
Posts
780
Reaction score
563
Location
Detroit
There is evidence that geisers will cause failure of the top hats, the increased spring rate can cause this, its been documented. So to be Geisers are just a no go in the first place, for me at least.

Also you are going to be sorry you did the icon upper control arms, the delta joint is junk. Wasted so many hours with those on my buddies rig.

Id stop adding more things thinking you'll make it better.
 

eurospek

Active Member
Law Enforcement
Joined
Sep 26, 2025
Posts
186
Reaction score
154
Location
Algonquin, IL
I’ve heard mixed reviews on the springs. Westcott designs installed on their shop truck and was not impressed. I’ll be going the Index top hat route when I do actually commit to leveling my 802a.
 

RaptorBros

Member
Joined
Dec 26, 2024
Posts
23
Reaction score
32
Location
Mass
This sounds like a Top Hat Bearing Failur I experienced numerous times. The uniball with all with the preload from the spring and top hat pulls down hard at full droop and pulls them apart. Need limit straps at a minimum and possibly switch to top hats with a rubber bushing from index or the SDI Top Hat.
 

RaptorBros

Member
Joined
Dec 26, 2024
Posts
23
Reaction score
32
Location
Mass
There are two different versions of the top hats from FMI. Get the HD ones or just get index or SDI versions. I had stock springs and it still happened repeatedly
 

Dudebrodude

Full Access Member
Joined
Sep 7, 2021
Posts
821
Reaction score
1,179
Location
Orange County, CA
Several people mentioned the top hats and they're right. I have replaced the uniballs in my foutz top hats twice. I went with probearing instead of the FK uniballs and they lasted wayyyy longer.

Either way, not an ideal design with all of the load on a spherical bearing like that. If I did it again, I would be going with the SDI top hat.
 

Dudebrodude

Full Access Member
Joined
Sep 7, 2021
Posts
821
Reaction score
1,179
Location
Orange County, CA
Several people mentioned the top hats and they're right. I have replaced the uniballs in my foutz top hats twice. I went with probearing instead of the FK uniballs and they lasted wayyyy longer.

Either way, not an ideal design with all of the load on a spherical bearing like that. If I did it again, I would be going with the SDI top hat.
Found the video of mine after a few hundred dirt miles.
 

EricM

FRF Addict
Joined
May 11, 2016
Posts
4,430
Reaction score
4,845
Location
OHIO
So it was the aftermarket parts. That's why the dealer doesn't want to touch modified trucks. They've been down that road.
 

BBX

Member
Navy
Joined
Oct 4, 2026
Posts
25
Reaction score
19
Location
Ca
The only way the spring could have caused damage to the shock is if the spring rate was too much for the shock to handle. This is common when guys do coil over conversions and use stock struts. You can have shocks rebuilt to match the coils rate. Are you able to call manufacturer of spring (geiser) and get the spring rate?
Did they remove the shock from the truck to test it or just deny warranty because of aftermarket shock? If the geiser spring rate is close to stock, maybe the clunking is coming from somewhere else. I've read the sway bar links fail early and cause clunking.
Did you check those?
 

Forum statistics

Threads
101,289
Posts
2,156,417
Members
60,424
Latest member
HC FabWerks
Top