Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Audio/Video/Electronics Forum [GEN 2]
Dsp input /output voltage
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="greatone99" data-source="post: 1826875" data-attributes="member: 35646"><p>I assume the 70 percent is for low recorded music ,aka headroom. im pretty happy where it is -10db as of now I've set and reset them again , at about 4v out of bit one my noise floor is gone which is about -10db on the dsp levels ,when I complained about noise floor before ,u were correct the gain on the amps tweeter channel was 2 high .the audison amp goes from 0-5 on the gains ,im 2.8 tweeter channel , 3.5 mids ,3.5 bass set that at -5 db noise I set all those with my scope ,I think it was 17.5 volts tweeters , 23.5 mids ,55 for subs ,I time aligned the speakers ,use the mic for db output ,adjusted the channel outputs relative to the drivers seat ,had to tone down the driver side speaker s.I installed the drc .I played around on the software ,looks like u can hook up a mic to the computer ,open up the bit one software ,it has a built in rta ,and it can self calibrate all the channels eq, may play with that soon . I switched between the tuned front active ,to not tuned ,not time aligned ,its night and day ,best thing I ever did was go active and add dsp. it went from what I through was a good system ,to a great sounding system ,with only 4 speakers and 2 subs</p></blockquote><p></p>
[QUOTE="greatone99, post: 1826875, member: 35646"] I assume the 70 percent is for low recorded music ,aka headroom. im pretty happy where it is -10db as of now I've set and reset them again , at about 4v out of bit one my noise floor is gone which is about -10db on the dsp levels ,when I complained about noise floor before ,u were correct the gain on the amps tweeter channel was 2 high .the audison amp goes from 0-5 on the gains ,im 2.8 tweeter channel , 3.5 mids ,3.5 bass set that at -5 db noise I set all those with my scope ,I think it was 17.5 volts tweeters , 23.5 mids ,55 for subs ,I time aligned the speakers ,use the mic for db output ,adjusted the channel outputs relative to the drivers seat ,had to tone down the driver side speaker s.I installed the drc .I played around on the software ,looks like u can hook up a mic to the computer ,open up the bit one software ,it has a built in rta ,and it can self calibrate all the channels eq, may play with that soon . I switched between the tuned front active ,to not tuned ,not time aligned ,its night and day ,best thing I ever did was go active and add dsp. it went from what I through was a good system ,to a great sounding system ,with only 4 speakers and 2 subs [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
Johnny Raptor
rushneck
Hambone
ben2jz
2010 Shelby
shigman
West Coast Raptor
RaptorJoe331
nikhsub1
AKSteve
Sergio212
Granelli
Rednose
Raptor Rob
KMO
taquitos
MyRaptor23LikeMJ
downforce137
OwenTM
jm77
The Car Stereo Company
Turning Blue
Forum statistics
Threads
92,828
Posts
1,946,510
Members
56,082
Latest member
JTRaptor20
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford Raptor Audio/Video/Electronics Forum [GEN 2]
Dsp input /output voltage
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top