Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
Ford Raptor Forums - General Information
Ford Raptor How-To's and FAQs
¡Más! Factory Upfitters & Easy Access wiring!!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Sitdown" data-source="post: 599727" data-attributes="member: 8674"><p><span style="color: DarkOrange"><span style="font-size: 18px"><strong>PART 2 - Dash Mounted Switches</strong></span></span></p><p></p><p>The console removal can be another thread in itself, see end of the thread for a link to Busa’s DIY Video for dash disassembly, or PM me and I can walk you through it. I’ve had my dash apart a handful of times now for NAVTV issues.</p><p></p><p><span style="font-size: 15px"></span></p><p><span style="font-size: 15px"><strong>Console Nook removal </strong></span></p><p></p><p>I chose the right storage pocket for my switches, as the left side was occupied by my trailer brake. If you do not have a trailer brake, I recommend using the left side nook for your switches, as it requires less “clearancing”.</p><p></p><p>[ATTACH=full]226049[/ATTACH]</p><p></p><p>With the side console cover removed, you will need to make the switch opening. I cut the storage pocket off close to the cover base and carefully dremeled down the material until I got flush with the inside of the grey cover. Later learned an easier approach might be to carefully drill out the 2 plastic rivets, and then the pocket can be more easily removed. With the console cover opening free of the pocket, you are now able to mock up the switch block and understand how much clearancing is necessary. </p><p></p><p>[ATTACH=full]226050[/ATTACH]</p><p></p><p></p><p></p><p><span style="font-size: 15px"><strong>Dash clearancing</strong></span></p><p></p><p></p><p>With the underside dash frame exposed, you will need to make room for the switch block. With a dremel (or your preferred cutting device), begin widening the opening in the plastic dash support. Take your time and continue until your switch block will fit (my initial fitments were done without the switch block bezel on, its clips on/off). </p><p></p><p>You will eventually trim a small amount of material off the ends of the switch bezel as well, but gradually clearance this and the opening until your switch panel fits. Keep intact two square openings , as these accept the console panel clips. One is to the lower left of the switch block opening, the 2nd is below and to the right. There isn’t much additional room side to side, so grinding/cutting down gradual and evenly was my tactic.</p><p></p><p>Pics of sides cut</p><p>[ATTACH=full]226051[/ATTACH]</p><p></p><p>[ATTACH=full]226052[/ATTACH]</p><p></p><p> [ATTACH=full]226053[/ATTACH]</p><p></p><p>[ATTACH=full]226054[/ATTACH]</p><p></p><p>[ATTACH=full]226055[/ATTACH]</p><p></p><p>I excessively taped off the whole dash initially, but some final tweaks later in project without protection left me with a nick in paint. Luckily that portion of the dash is covered by one of the console covers.</p><p></p><p>[ATTACH=full]226056[/ATTACH]</p><p></p><p></p><p>While the driver’s side nook will not have this issue, my passenger side required some additional clearancing of the aluminum dash brace. Given the minimal space to get a dremel in, I choose to make a single cut, and fold a portion of the brace back to give the switches room to insert fully. I used a hammer and extension, but a dremel adapter might be less of a caveman approach. Once the switch block fits, begin to mock up the side console cover to confirm alignment. Additional steps of clearancing may be required to get the correct alignment, using just the switch bezel alone is an easier process for alignment. </p><p></p><p>Opening showing alum frame cut and bend</p><p>[ATTACH=full]226057[/ATTACH]</p><p></p><p>[ATTACH=full]226058[/ATTACH]</p><p></p><p></p><p></p><p>Once clearance and alignment is good, use your preferred plastic adhesive to glue the bezel to the console cover. My adhesive (3M ??) was slightly corrosive to the bezel plastic, so using less for the first round is recommended, to avoid glue running. I let my adhesive sit for several hours, and confirmed fitment again with just the bezel installed on the cover. Once all was good, I clipped the switch block into the switch bezel on the console cover and reinstalled all the dash components. The switch block is still easily accessible for attaching the harness, you will reach around through the glovebox and plug in your harness.</p><p></p><p></p><p>Mock up bezel on console cover</p><p>[ATTACH=full]226059[/ATTACH]</p><p></p><p>w/ switches</p><p>[ATTACH=full]226060[/ATTACH]</p><p></p><p>Final look</p><p>[ATTACH=full]226061[/ATTACH]</p><p></p><p>[ATTACH=full]226062[/ATTACH]</p><p></p><p>[ATTACH=full]226063[/ATTACH]</p><p></p><p>Pic at night</p><p>[ATTACH=full]226064[/ATTACH]</p><p></p><p></p><p></p><p></p><p></p><p></p><p><span style="color: DarkOrange"><span style="font-size: 18px"><strong>Easy Access Forward Junction Box</strong></span></span></p><p></p><p></p><p>I probably had a hundred feet of wasted wire from previous light setups that were eventually bundled into another loom, and later cut and left. To clean/organize things up and simplify upgrades/changes down the road, I chose to add this sealed junction box up towards the front of the truck, closer to the accessories. The box is sourced off amazon, see end of thread for details.</p><p></p><p>This box can be mounted anywhere in the engine bay area, for easiest access I chose to mount mine beside the passenger headlight ( behind the rubber splash guard). I included above a template to make a bracket for holding your box, it bolts up using 2 of your factory headlight housing screws. </p><p></p><p></p><p>Bracket bare metal</p><p>[ATTACH=full]226065[/ATTACH]</p><p></p><p>[ATTACH=full]226066[/ATTACH]</p><p></p><p>Textured</p><p>[ATTACH=full]226067[/ATTACH]</p><p></p><p>[ATTACH=full]226068[/ATTACH]</p><p></p><p>[ATTACH=full]226069[/ATTACH]</p><p></p><p></p><p>Using the same type of distribution blocks as I used on the relay panel, I glued 3 in the box. 1 for the new switch block source powers (lights/accessories), 2nd for the factory switch block source powers, and 3rd is a shared ground for both switch block source grounds. The middle block is elevated higher for tiered wiring</p><p></p><p></p><p></p><p>Juncbox on bench</p><p>[ATTACH=full]226070[/ATTACH]</p><p></p><p>[ATTACH=full]226071[/ATTACH]</p><p></p><p>Shown with brackets installed</p><p>[ATTACH=full]226072[/ATTACH]</p><p></p><p>[ATTACH=full]226073[/ATTACH]</p><p></p><p></p><p></p><p>I drilled 4 holes in the bottom of the box for wiring IN & OUT, used some rubber grommets and barriers to keep elementns away from the distribution blocks</p><p></p><p>Open with first set of sources fed</p><p>[ATTACH=full]226074[/ATTACH]</p><p></p><p>[ATTACH=full]226075[/ATTACH]</p><p></p><p>[ATTACH=full]226076[/ATTACH]</p><p></p><p>Back side</p><p>[ATTACH=full]226077[/ATTACH]</p><p></p><p></p><p>Mounted open</p><p>[ATTACH=full]226078[/ATTACH]</p><p></p><p>Painted - cover</p><p>[ATTACH=full]226079[/ATTACH]</p><p></p><p></p><p>Covered box - top</p><p>[ATTACH=full]226080[/ATTACH]</p><p></p><p>Covered box</p><p>[ATTACH=full]226081[/ATTACH]</p><p></p><p></p><p></p><p></p><p></p><p>Conclusion:</p><p></p><p>Definitely a lot of work for “just a few switches”, but if you want the clean look this appeared to be the best route to me. If there is another way to save time, do something better, or more efficiently I absolutely encourage any opinions/comments/feedback. </p><p></p><p>***Disclaimer - I am not an accredited electronics installer, electrician, mechanic, dentist, or superhero. This write-up is for recreational purposes, proceed at your own risk.***</p><p></p><p>That said, if you have any questions feel free to PM me, I’m happy to help out in any way I can.</p><p></p><p></p><p></p><p></p><p>Parts Used:</p><p>*Ford Upfitter Switch Panel (PN AL3Z13D730AA Switch Assy 11 F-Series Super Duty - $60)</p><p>(<a href="http://www.ebay.com/itm/AL3Z13D730AA-Switch-Assy-10-F150-/390566438068?pt=Motors_Car_Truck_Parts_Accessories&hash=item5aef92e4b4" target="_blank">AL3Z13D730AA Switch Assy 10 F150 | eBay</a> )</p><p>*Ford Wiring Harness for Switch Panel (PN 3U2Z14S411DLB Wire Assy 10 E150 -$35)</p><p>(<a href="http://www.ebay.com/itm/3U2Z14S411DLB-Wire-Assy-10-E250-/350763840929?pt=Motors_Car_Truck_Parts_Accessories&hash=item51ab2775a1" target="_blank">3U2Z14S411DLB Wire Assy 10 E250 | eBay</a> )</p><p>*Distribution/Terminal blocks – (6)x 30a (Avail at Local Parts Store -$4ea)</p><p>( <a href="http://www.oreillyauto.com/site/c/detail/CTI0/85685/N1177.oap?ck=Search_N1177_-1_2446&pt=N1177&ppt=C0172" target="_blank">Dorman® Conduct-Tite!™ 85685 - Junction Box | O'Reilly Auto Parts</a> )</p><p>*Fuse Block (Avail at LPS -$10)</p><p>( <a href="http://www.autozone.com/autozone/accessories/Cooper-Bussmann-6-position-ATC-fuse-panel/_/N-25gq?itemIdentifier=32322_0_0_" target="_blank">Cooper Bussmann/6 position ATC fuse panel (BP-15600-06-2) | Fuse and Accessories | AutoZone.com</a> )</p><p>*Relays (Bosch Type) & Relay Socket – (4)x 30a ( Avail at LPS - $5) </p><p>*Misc sheet of alum/steel/plastic/etc for relay panel</p><p>*Misc Wire</p><p>*Eyelets & Slip connectors </p><p>*Weatherproof Junction Box (Optional - for easy access front panel)</p><p>([ame=http://www.amazon.com/gp/product/B00E0GLLXA/ref=oh_details_o09_s00_i01?ie=UTF8&psc=1]158mm x 90mm x 46mm Waterproof Plastic Enclosure Case DIY Junction Box - Amazon.com[/ame] )</p><p></p><p></p><p>Our very own CarStereoCompany & IceCobra made a DIY video of removing the dash panels, which can be viewed here:</p><p><a href="http://www.fordraptorforum.com/f170/nav-tv-install-radio-removal-directions-21732/" target="_blank">http://www.fordraptorforum.com/f170/nav-tv-install-radio-removal-directions-21732/</a></p><p></p><p>I’ve had my NAVTV in and out a handful of times so am happy to guide anyone through the dash removal or again, any steps to this DIY. </p><p></p><p>Tom</p></blockquote><p></p>
[QUOTE="Sitdown, post: 599727, member: 8674"] [COLOR="DarkOrange"][SIZE="5"][B]PART 2 - Dash Mounted Switches[/B][/SIZE][/COLOR] The console removal can be another thread in itself, see end of the thread for a link to Busa’s DIY Video for dash disassembly, or PM me and I can walk you through it. I’ve had my dash apart a handful of times now for NAVTV issues. [SIZE="4"] [B]Console Nook removal [/B][/SIZE] I chose the right storage pocket for my switches, as the left side was occupied by my trailer brake. If you do not have a trailer brake, I recommend using the left side nook for your switches, as it requires less “clearancing”. [ATTACH=full]226049[/ATTACH] With the side console cover removed, you will need to make the switch opening. I cut the storage pocket off close to the cover base and carefully dremeled down the material until I got flush with the inside of the grey cover. Later learned an easier approach might be to carefully drill out the 2 plastic rivets, and then the pocket can be more easily removed. With the console cover opening free of the pocket, you are now able to mock up the switch block and understand how much clearancing is necessary. [ATTACH=full]226050[/ATTACH] [SIZE="4"][B]Dash clearancing[/B][/SIZE] With the underside dash frame exposed, you will need to make room for the switch block. With a dremel (or your preferred cutting device), begin widening the opening in the plastic dash support. Take your time and continue until your switch block will fit (my initial fitments were done without the switch block bezel on, its clips on/off). You will eventually trim a small amount of material off the ends of the switch bezel as well, but gradually clearance this and the opening until your switch panel fits. Keep intact two square openings , as these accept the console panel clips. One is to the lower left of the switch block opening, the 2nd is below and to the right. There isn’t much additional room side to side, so grinding/cutting down gradual and evenly was my tactic. Pics of sides cut [ATTACH=full]226051[/ATTACH] [ATTACH=full]226052[/ATTACH] [ATTACH=full]226053[/ATTACH] [ATTACH=full]226054[/ATTACH] [ATTACH=full]226055[/ATTACH] I excessively taped off the whole dash initially, but some final tweaks later in project without protection left me with a nick in paint. Luckily that portion of the dash is covered by one of the console covers. [ATTACH=full]226056[/ATTACH] While the driver’s side nook will not have this issue, my passenger side required some additional clearancing of the aluminum dash brace. Given the minimal space to get a dremel in, I choose to make a single cut, and fold a portion of the brace back to give the switches room to insert fully. I used a hammer and extension, but a dremel adapter might be less of a caveman approach. Once the switch block fits, begin to mock up the side console cover to confirm alignment. Additional steps of clearancing may be required to get the correct alignment, using just the switch bezel alone is an easier process for alignment. Opening showing alum frame cut and bend [ATTACH=full]226057[/ATTACH] [ATTACH=full]226058[/ATTACH] Once clearance and alignment is good, use your preferred plastic adhesive to glue the bezel to the console cover. My adhesive (3M ??) was slightly corrosive to the bezel plastic, so using less for the first round is recommended, to avoid glue running. I let my adhesive sit for several hours, and confirmed fitment again with just the bezel installed on the cover. Once all was good, I clipped the switch block into the switch bezel on the console cover and reinstalled all the dash components. The switch block is still easily accessible for attaching the harness, you will reach around through the glovebox and plug in your harness. Mock up bezel on console cover [ATTACH=full]226059[/ATTACH] w/ switches [ATTACH=full]226060[/ATTACH] Final look [ATTACH=full]226061[/ATTACH] [ATTACH=full]226062[/ATTACH] [ATTACH=full]226063[/ATTACH] Pic at night [ATTACH=full]226064[/ATTACH] [COLOR="DarkOrange"][SIZE="5"][B]Easy Access Forward Junction Box[/B][/SIZE][/COLOR] I probably had a hundred feet of wasted wire from previous light setups that were eventually bundled into another loom, and later cut and left. To clean/organize things up and simplify upgrades/changes down the road, I chose to add this sealed junction box up towards the front of the truck, closer to the accessories. The box is sourced off amazon, see end of thread for details. This box can be mounted anywhere in the engine bay area, for easiest access I chose to mount mine beside the passenger headlight ( behind the rubber splash guard). I included above a template to make a bracket for holding your box, it bolts up using 2 of your factory headlight housing screws. Bracket bare metal [ATTACH=full]226065[/ATTACH] [ATTACH=full]226066[/ATTACH] Textured [ATTACH=full]226067[/ATTACH] [ATTACH=full]226068[/ATTACH] [ATTACH=full]226069[/ATTACH] Using the same type of distribution blocks as I used on the relay panel, I glued 3 in the box. 1 for the new switch block source powers (lights/accessories), 2nd for the factory switch block source powers, and 3rd is a shared ground for both switch block source grounds. The middle block is elevated higher for tiered wiring Juncbox on bench [ATTACH=full]226070[/ATTACH] [ATTACH=full]226071[/ATTACH] Shown with brackets installed [ATTACH=full]226072[/ATTACH] [ATTACH=full]226073[/ATTACH] I drilled 4 holes in the bottom of the box for wiring IN & OUT, used some rubber grommets and barriers to keep elementns away from the distribution blocks Open with first set of sources fed [ATTACH=full]226074[/ATTACH] [ATTACH=full]226075[/ATTACH] [ATTACH=full]226076[/ATTACH] Back side [ATTACH=full]226077[/ATTACH] Mounted open [ATTACH=full]226078[/ATTACH] Painted - cover [ATTACH=full]226079[/ATTACH] Covered box - top [ATTACH=full]226080[/ATTACH] Covered box [ATTACH=full]226081[/ATTACH] Conclusion: Definitely a lot of work for “just a few switches”, but if you want the clean look this appeared to be the best route to me. If there is another way to save time, do something better, or more efficiently I absolutely encourage any opinions/comments/feedback. ***Disclaimer - I am not an accredited electronics installer, electrician, mechanic, dentist, or superhero. This write-up is for recreational purposes, proceed at your own risk.*** That said, if you have any questions feel free to PM me, I’m happy to help out in any way I can. Parts Used: *Ford Upfitter Switch Panel (PN AL3Z13D730AA Switch Assy 11 F-Series Super Duty - $60) ([url=http://www.ebay.com/itm/AL3Z13D730AA-Switch-Assy-10-F150-/390566438068?pt=Motors_Car_Truck_Parts_Accessories&hash=item5aef92e4b4]AL3Z13D730AA Switch Assy 10 F150 | eBay[/url] ) *Ford Wiring Harness for Switch Panel (PN 3U2Z14S411DLB Wire Assy 10 E150 -$35) ([url=http://www.ebay.com/itm/3U2Z14S411DLB-Wire-Assy-10-E250-/350763840929?pt=Motors_Car_Truck_Parts_Accessories&hash=item51ab2775a1]3U2Z14S411DLB Wire Assy 10 E250 | eBay[/url] ) *Distribution/Terminal blocks – (6)x 30a (Avail at Local Parts Store -$4ea) ( [url=http://www.oreillyauto.com/site/c/detail/CTI0/85685/N1177.oap?ck=Search_N1177_-1_2446&pt=N1177&ppt=C0172]Dorman® Conduct-Tite!™ 85685 - Junction Box | O'Reilly Auto Parts[/url] ) *Fuse Block (Avail at LPS -$10) ( [url=http://www.autozone.com/autozone/accessories/Cooper-Bussmann-6-position-ATC-fuse-panel/_/N-25gq?itemIdentifier=32322_0_0_]Cooper Bussmann/6 position ATC fuse panel (BP-15600-06-2) | Fuse and Accessories | AutoZone.com[/url] ) *Relays (Bosch Type) & Relay Socket – (4)x 30a ( Avail at LPS - $5) *Misc sheet of alum/steel/plastic/etc for relay panel *Misc Wire *Eyelets & Slip connectors *Weatherproof Junction Box (Optional - for easy access front panel) ([ame=http://www.amazon.com/gp/product/B00E0GLLXA/ref=oh_details_o09_s00_i01?ie=UTF8&psc=1]158mm x 90mm x 46mm Waterproof Plastic Enclosure Case DIY Junction Box - Amazon.com[/ame] ) Our very own CarStereoCompany & IceCobra made a DIY video of removing the dash panels, which can be viewed here: [url]http://www.fordraptorforum.com/f170/nav-tv-install-radio-removal-directions-21732/[/url] I’ve had my NAVTV in and out a handful of times so am happy to guide anyone through the dash removal or again, any steps to this DIY. Tom [/QUOTE]
Insert quotes…
Verification
Post reply
Staff online
Griffin
Administrator
Members online
FreightTerrain
rplaxsun
WNCHSTR96
sc85fiero
eljefe_tx
nomis88
Dano182
sct
JeepSRT8
Vettster
Keith88
Aird_outSRT
Rddakota
julien194b
kevo_lo
thatJeepguy
XCReapor
mprice1234
wyomingraptor
OEMPlus Raptor
awd5906
dirtslinger
ToadSmasher2K1
DaveInMn
isis
signalbobby
shigman
darkslide750
CleverGirl_
quattrojim
XtraSpclCrspy
Sharpie69
alockbox
BadWRP
jAKe47
Jesse1983
Griffin
FJohnny
twoputtbirdie
RaptorFun
DMacDonald
AmaRaptor
NickyF25
IHAVETWO
BoostCreep
JD05
Gatica
RaptorJoe331
tlrmade
vill
... and 56 more.
Forum statistics
Threads
93,165
Posts
1,955,137
Members
56,439
Latest member
jumpcutter
Forums
Ford Raptor Forums - General Information
Ford Raptor How-To's and FAQs
¡Más! Factory Upfitters & Easy Access wiring!!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top