Search results

I know this has been asked a few time. I've searched and read through similar threads, but need clarity around an issue I have. I have a problem with my puddle light circuit, and that is also keeping my cargo light to not work. I have code B12C2 stored in the BCM. Puddle Lamp - Circuit Short...

Has anyone replaced their body mounts on their Gen 1? I know there's options to do the solid mounts, but I did not want to go that route yet. So trying to get a set of body mounts has proven to be quite challenging. You can look at O'reilly, Autozone, Rock Auto, Etc. I can only find the...

I’m hearing a clunk or thud when I hit a moderate or larger bump. It sure sounds like rear left. I’ve had it in a shop looking for what’s going on to no avail. I have fix 3.0 by pass shocks. Some say the shocks make noise. If it was the shocks, I would think I hear it on both sides. The shocks...

Seems to be the go to on tunes for the Gen 1's are 5star, Livernois, or JDM. Is anyone running Lund? They don't advertise on the Gen 1's but pretty sure they will still work with them if you ask. Just curious if anyone has run a tune of theirs with a boosted/modified 6.2 Platform.

I'm having some issues with my MAF. Kind of a rough idle and it sounds a little different. 2014, 6.6L + SC on E85. I've been driving the 6.6 for about 9 months without any issues. First I had P1101 pop in Forscan. MAF sensor out of self test range. When I look at the MyCalibrator gauges...

I’ve had the moritomo xb’s in my 14 screw for a few months. My passenger side headlight will hyper flash the turn signal when in drive with headlights off. When I use the turn signal, the turn signal flashes as it should. I have my DRL set to be on with forscan and all hyper flashing off with...

I'm needing some help please. I have a 2014 SCREW Raptor. I have a draw and cannot find it. It shows to be in the puddle light circuit per Forscan. I did change over puddle lights to LED and also added LED to front and back of the mirrors. All of my wire connections are soldered and shrink...

If there is a misfire on a cylinder, will it 100% of the time throw a CEL? I've got a little bit of a rough idle. 6.6L + SC. I have Forscan, but don't necessarily see a misfire test there as shown in some of the Forscan youtube videos. It could be a dirty MAF sensor? What methods would...

When I put the whipple on the 6.2L motor, I had a heck of a clunk when stopping and taking off. Also loud clunk if a downshift from say 4th to 3rd. With the whipple, I also had an axle exchange DS installed with chrome molly slip yolk. I took the DS off and greased the splines and that worked...

I'll just give the latest on my transmission. The 2nd time I got it back, all seemed to be good. Then I started feeling a catching in reverse. I thought - Maybe it's the parking brake/brakes. I replaced all rotors and pads, and installed those. No change. Adjusted the parking brake many...

Here's a summary. I had MS Racing in Florida rebuild my transmission. Fully built, supposed to handle up to 1200 WHP. After about 2 months, a solenoid on the valve body stuck, and this in turn allowed the lower planetary to fail as well as the one way clutches. The valve body was installed...

Does anyone have a rear bump stop kit they’d let go? Deaver springs should arrive Friday. Thought I’d kick a few rocks here before I drop $$ for new.

On 7/22, a semi-local drag strip has their truck night races. I'm going to take my raptor and just see what it will do. Looking for any tips and suggestions. I could launch in 2nd gear. Thoughts on that? I would assume that I should lock the rear differential and run it that way? My torque...

So I read a few of the threads about the notorious driveline clunk. I've had it ever since I changed out the drive shaft for one from Axle Exchange. I took my drive shaft off this weekend and filled inside of the splined end with grease and re-installed. Clunk gone. The shop that last...

So with my transmission built now, I foresee next problem areas either transfer case or rear end. Has anyone blew up a transfer case? I see that SDHQ is a go to for the rear end. Any other suggestions to hold the power level on my truck with the drive line? I have my truck back in the shop...

A couple of months ago, I pulled a 20’ car trailer loaded with a 4500 lb car on the trailer. When I pulled the car up on the trailer where I would normally park, the shocks on my raptor were squatting bad. I have the Fox 3.0’s on the rear. Only have 2000 miles on the shocks. My springs are...

I'm down for a bit with my Gen 1 while the tranny is getting pulled, and sent out for rebuild. I have some other goodies that need worked on while it's down. I have Blitkrieg UCA's to install, as well as Blitkrieg tie rods to get put on. Might as well do the lca ball joints and bushings...

Has anyone used HPP racing on here for tuning a Gen 1 raptor? They are out of Garland, TX. Looks like they prefer dyno tuning, but will tune how you want.

I have 2014 Screw with 6.6L, whipple, lots of boost and E85. I finally got things together and bought a 16’ +4’ dove tail trailer to pull my hellcat on. I strapped it on the trailer and headed to my tuner before I start back at the track. About a 2.5 hr drive each way and being in NW Arkansas...

Needing help with Forscan please. I got it all setup and going on my laptop with the free extended license. Enabled DRL, dropped TPMS value to 36 PSI, and made a few other tweaks. All that I've done is through the easy access menu. I've read about the spreadsheet and the as-built. I also...

Hello. I was wanting to see if I could get some input. I've started suspension mods on my trucks. 2014 Gen 1 Screw. Installed the Gen 2 fox race 3.0 shocks/coil overs on the front with use of the new buckets. Installed new tires. 35's. Mickey Thompson Legend EXP's I had the truck...

A week or so ago, I ordered a cheap LED kit for converting interior bulbs for LED’s. I changed out the dome light, map lights and cargo light bulbs. The LED’s are bright and all looks good. Until I let the truck sit for about a day. Battery was dead as dead can be. So from some quick...

My shocks need an upgrade. 2014 Gen 1 with 85K miles, no work done on suspension. Does anyone have a set of shocks that would be an upgrade? I’m still pretty new to the suspension side. I saw where I can get the bracket to bolt on to run the 3.0's in the rear as well as the hat to run the...

I started to throw the code P0153 - O2 circuit slow response - the last couple of days. Bank 2 sensor 1. So driver side, upfront of my cat. Yes, running GESI cats with ARH LT headers. It didn’t look bad to change at all, so I stopped at O’Reilly’s and they said the upfront driver side is Bosch...

I was able to get in a dyno pull on 02-02-23. Fuel was pump E85. Literally driving 120 miles and within 30 mins this is what I saw. I’m headed back in a few weeks and will get in a pull on drum e85. Might make a little difference. We shall see. 2014 F150 Raptor 6.6L Livernois Long Block...