Search results

Gen 1 transmission pan gaskets. When I originally ordered they sent 2, so there are 2 in the box. Free pickup in Austin or pay for shipping

Gen 1 parts 2X MOOG inner tie rod end: #EV800457 1X Motorcraft outer tie rod end #MEOE145 Bought these as spares for my Gen 1 Raptor. New never used. $40 shipped or pickup in Austin Sent from my iPhone using Tapatalk

One bushing is torn, not sure if they are replaceable. Passenger side Free pickup in Austin or just pay for shipping Sent from my iPhone using Tapatalk

These towing mirrors can be adjusted to go super wide. Worked very well on my truck. I purchased from here: http://www.dyersonline.com/dometic-g...xoC9ZsQAvD_BwE $50 shipped

Only used a few times. Clip right on factory mirrors, very easy to use. Model 81810 $35 shipped Sent from my iPhone using Tapatalk

Part #446131 1 year old. Fit 2010-2014 Raptor and F150. Sold truck $80 shipped Sent from my iPhone using Tapatalk

Volant throttle body spacer part #729850 New at Jegs $46 $30 shipped Sent from my iPhone using Tapatalk

Performance Automatic Dipstick. A must have for checking transmission level. The factory way to check is an absolute pain. Installed in 15 minutes. $185 new from SDHQ $120 shipped Sent from my iPhone using Tapatalk

Drivers side LCA, had as a spare, sold truck $250 shipped Sent from my iPhone using Tapatalk

Sold truck Fits raptor and any vehicle with a 6R80 transmission A must for towing or off-roading, adds several additional quarts of trans fluid, also makes it very easy to do fluid swaps, no dropping the pan. Super easy install. $145 shipped $190 new Sent from my iPhone using Tapatalk

Sold truck Fits Raptor and any ford with a 12 bolt 9.75" rear end. For towing or off-roading it's a must to keep rear end temps down. Very easy install. $200 shipped $265 new Sent from my iPhone using Tapatalk

Sold truck, installed for 5000 ish miles. Super easy install, basic hand tools is all required. $875 shipped Sent from my iPhone using Tapatalk

Bought during the group buy, never got around to installing. $500 shipped. Sent from my iPhone using Tapatalk

Sold truck Were on truck for about 5500 miles. Local only unless you have some connection for shipping. $850 Sent from my iPhone using Tapatalk

Sold truck. On truck for 5k miles. Fantastic intake, fit is perfect. $250 shipped. Sent from my iPhone using Tapatalk

Sold truck. Sweet sounding exhaust, not to loud, very little drone, not as bad as others I've heard. No sounds clips, there are some threads on this board with some. Added extra hanger mounts for raptor runs. $200 local to Austin TX and surrounding areas Sent from my iPhone using Tapatalk

Parting out truck. I made these for the raptor runs. Worked fantastic I'm a hobbyist welder so the welds are not perfect, but they are strong. $150 shipped Sent from my iPhone using Tapatalk

Is it ok to tow with the bumps so close to the axle? I would think so. Deavers are +2's Sent from my iPhone using Tapatalk

Wanted to create a checklist that we could all refer to for reference either before or after some hard off road use. Add to the thread and I will continue to update the list so it's current and you won't have to read through pages. Torque Specs...

I made this for the 2012 Raptor run. $200 Local pick up in Austin TX only Cage uses the front bed bolts and you must drill two 3/8" holes for the other mounting tabs. There are various tie downs on the cage to secure the gear.

I noticed after the Raptor Run that the underneath of the truck more specifically the plastic shock guards get beat to hell from rocks and such, I also noticed the emergency brake line and ABS lines are subject to flying debris, so I covered them in vacuum hoses. Problem solved! Just take a...

I’ve had the opinion that when breaking in a new vehicle that the fluids should be changed at 1500 miles, as I believe after the first 1500 miles the lubricated parts have had enough time to break in. I have always been one to like Redline products and this truck will be no different. So my...

I made this for the Texas Raptor Run. It worked very well and was actually a bit overkill for the event. But I built it this way as I didn't know what to expect. I really didn't need the gas cans, or ice chest, but oh well it's there now unless I cut the cage up which I probably won't...

Tonight was time for removal of the sway bar. I wanted to remove this for this weekends Raptor Run. Removal of the sway bar will allow the L or R suspension components to operate individually instead of being tied together with the sway bar. In an off road environment this is what I want...

My truck is a 2012 super crew and had 200 miles at time of install. I did this in my garage, was kind of a pain in the ass, very tedious trying to tighten all the bolts properly. Notes from my install: 1. You will need jack stands and 2 floor jacks, one for raising/lowering the diff and...