Search results

The Deaver HD's would help a lot with that as they have a 500lb preload.

I worked with Deaver as well and we went with stock height which I believe is +2 HD springs for me. My wake boat is about 7k lbs. the ride without towing is still much better than the factory springs. I also installed the Camburg bump stop kit. Not sure I actually needed this or not as...

Definitely get a WD hitch. But if you plan on towing a lot and keeping your truck you should also upgrade your springs to Dever HD’s. These give you a 500lb preload and makes a big difference with higher tongue weights. I tow a 23 ft wake boat and its made a massive difference. I also got...

I agree with B&W. Great hitch with lots of options. I have the 5 inch with 3 ball sizes. Works great.

My bad. Gen 2.

I have the retrax and it works great. This is my second retrax cover.

I have a 37 spare that replaced the 35 spare. My wheels are 17 inch and its fits just fine.

My hitch wasn't level either. I took it in and had them replace it. I would highly recommend you get it replaced and always use a weight distribution hitch. The Raptor is a horrible tow vehicle. Be safe

I did the Camburg set that uses Fox Bump stops. I'd recommend putting the Deavers on at the same time. Will probably run you about $3,000 all in....

I have the Retrax Pro MX. Its been great. Also had one on a prior truck. No issues and looks great.

I use the e2 as well to tow a Nautique G23. Boats head y at about 7k lbs with close to 600lb tongue weight. I have 2" Deavers and the Camburg bump stops. Seems to work great. I did have to have Ford replace my hitch as the original had a slight negative angle. Otherwise, everything is good.

I have Deaver +2 HD's and the back is at factory height without any load.

I have the Icon collar set at 1.5 inches up front and the Deaver HD at Standard Height (+2's) The HD's are a little stiffer, but we tow a heavy wake board boat and wanted the extra stiffness for that. I do get a little rubbing in the front with the 37's, even after some trimming, but its...

I had my truck coated with Ceramic Pro about a year ago. It cost about $2k, but the truck literally still looks new. Might be worth the extra investment.

I have auto stop eliminator as well, but absolutely hate the light. Can you pop off the cover for the switch without pulling the dash apart? I'd like to add the tape on the light. Appreciate the help.

Yes. I put on 37 KO2's and the spare fits fine on 17's....

I installed the slotted drilled rotors and new pad by R1, but didn’t change the calipers. You’ll need to make sure they fit with the 17’s.

The ICON Collar is for the front only. The 1.5 inch setting will level the front with the back. The Deavers I put on are are the same height for the rear as the factory springs. My understanding is if you go with the Geiser springs the front will be about 1 inch taller than the rear at the...

Yes. Used the Icon collar to level at the 1.5 inch up setting. Also have Deavers at standard hight in the rear. Went with the Camburg upper control arms and their bump stop kit. Truck rides great.

17 Icon Compression Wheels with 37 BFG AT's. Great wheels. Other color combinations available.

I installed the Deavers and would agree it was the best thing I've done so far. Downside to the extra cost of Deavers is you'll also need to change the bumpstops. Current bumpstops and springs are a joke. I promise this upgrade will be one of your best.

Thanks

https://www.bajadesigns.com/products/Ford-Raptor-2017-Fog-Pocket-Kit-Unlimited.asp

I just put 37 K02's on along with ICON wheels, Deavers HD at Standard Height, and Camburg Upper control arms and fox bumps top kit. I leveled with the ICON collar at 1.5 a few months ago. What a difference.

Just ordered my front and rear upgrade today for my 2019. Great deal. Much appreciated....