Search results

  1. JimT

    2010 Tranny shifting issue

    When I hooked up the programmer and checked for codes, it said there were none. However during one of the episodes where it failed to shift from 4 to 5 cleanly and engine RPM's came up, I did get the Wrench display on my dash and noticed I was locked out of 6th gear until I shut the engine off...
  2. JimT

    2010 Tranny shifting issue

    I have an SCT programmer that I think reads codes, only time I used it was to install a 5 start tune. :)
  3. JimT

    2010 Tranny shifting issue

    Having an issue with Transmission shifting, NEED HELP/ADVICE. 2010 Raptor, 160k miles, Recent partial fluid & Filter change. When auto shifting in residential and side streets, 1/2, 2/3, 3/4 shift normal but from 4 to 5, engine revs like in neutral with throttle barely applied when maintaining a...
  4. JimT

    New Guy from Oklahoma

    Nice looking "Stangs" I'm in Owasso.
  5. JimT

    HELP needed on locating the climate control fan module

    Thanks so much xtela, this is a great help.
  6. JimT

    HELP needed on locating the climate control fan module

    Phydough do you know where on the vehicle the module is located? Thanks, Jim ---------- Post added at 12:05 AM ---------- Previous post was at 12:02 AM ---------- Not sure what you mean by flow thru floor consoles, I have the vents on the back side of the console. I have a '10 SCAB with...
  7. JimT

    HELP needed on locating the climate control fan module

    I have a '10 and my fan is stuck on high speed. every thing else works on the climate control, temp, what vent to direct air etc. but the fan will not change speeds. Where is this module located so I can see which item to buy, apparently there are 2 different ones avail for our trucks...
  8. JimT

    Climate Control Stuck on High

    I have a '10 that is experiencing the same issue as above with the fan stuck on high speed. Is there a DIY on how to get to this part? where is it located? I assume under the dash somewhere, lol and of the 2 part numbers listed which would be the correct one. Thanks, JimT
  9. JimT

    Owners with graphics how's it holding up so far?

    I would like to someday change mine from the OEM digital mud to something custom but I'm afraid to try and remove the OEM and find the Molten Orange color darker where the graphics were compaired to where the sun has maybe lightened the rest of the truck. lol
  10. JimT

    Owners with graphics how's it holding up so far?

    I know you asked about '12 +, but my '10 has sat outside since new and my digital mud graphics show no sign of fading or lifting. Very happy with the OEM graphics.
  11. JimT

    2010, 6.2 throwing codes related to vacuum

    According to the troubleshooting guide it looks like the code I'm seeing (P1450) maybe a leaking or stuck open CPV. MTF do you know where this valve is located? Is it in the engine compartment, drivers side?
  12. JimT

    2010, 6.2 throwing codes related to vacuum

    9pm and I am now looking at the PDF, dang there are alot of pages and info to try and sort through. lol this may take a while.
  13. JimT

    2010, 6.2 throwing codes related to vacuum

    MTF, I'm at work and wont be able to view it till I get home tonight. lol Damn work messing with my Raptor troubleshooting time!!!
  14. JimT

    2010, 6.2 throwing codes related to vacuum

    Crystal, would the problem I'm experiencing be covered on Fords emission warranty? Mine is a '10 with 55k miles. and if not, do you have an idea what part or parts may be faulty?
  15. JimT

    2010, 6.2 throwing codes related to vacuum

    Yes please report back. MTF, yes I think I will need that PDF file.
  16. JimT

    2010, 6.2 throwing codes related to vacuum

    The code is 1450, unable to bleed up fuel tank vacuum. where would the vapor management valve be located? is it part of the canister, or located on the engine or?
  17. JimT

    2010, 6.2 throwing codes related to vacuum

    It started about 7 weeks ago with "check fuel fill line" or something similar to that. Someone on the forum facebook page said to check the canister which found, I checked all the connections and all seemed fine. I cleared the code with my programmer and all was good for about a week. Then I...
  18. JimT

    LED vs Halogen

    Raptor Embroidery: Sweet looking truck. Love the lights.
  19. JimT

    **official MFT backgrounds thread**

    on the 2010 trucks you have to burn to a CD but not sure on the '11 and newer ones.
  20. JimT

    LED vs Halogen

    This may be a little old school for some but this combo of round Halogen on top and LED's underneath works great for me.
  21. JimT

    R.I.P.

    I agree the SE Ruby red is damn nice looking, 2nd choice would be red.
  22. JimT

    STOCK Front bumper sellers

    Around $300.00 would be about normal but at that price they don't sell too fast. lol I have one for sale and have not been able to sell it yet. I'm thinking about dropping the price again.. And mine is like new.
  23. JimT

    Plashlights

    lol well it is a combination of lights I had from other vehicles. The center light is a 9" ROD HALL light bought waaaaaay back when **** Ceepek had a store in San Diego. The 2 lites beside it are PRO COMP 9", these 3 all run 130w halogen bulbs. The outside 2 are HELLA 6" 500 series driving...
  24. JimT

    Plashlights

    Not trying to steal this thread but here is a company that sells a wide variety of LED light bars. Their web addy is MicTuning.com,Cree LED lights bar` I bought 2 of the 4.5" 20w CREE light bars for fog lites and the 22" bar also using the CREE 10w LED's as more of a long distance off-road light.
Top