Search results

Opposite end of where the cv shaft seats, there's an O ring that sits on the base of that spline. There's videos on YouTube showing that it can sometimes come off when replacing the passenger side.

If the blower motor isn't spinning start with the resistor. I had an issue where the AC was not keeping up, temp and air flow wise. There was a blend door actuator that wasn't working properly, but it was just the one under the driver side in charge of air flow direction,. I changed it but...

thanks, I'll have to take a look, theses were what the previous owner had on them.

Thought I'd share my little adventure. I was driving from North Carolina back to Texas and look what happened. A lug nut fell off at some point (the chrome one), then 2 more sheered off, then the other 3 became loose. I managed to find some lug nuts at an auto parts store in Mississippi to fit...

straight bolt on. no other mods needed. The front shocks come with their own upper mount hardware but everything else is reused hardware. I'm currently on stock leaf springs and stock upper and lower control arms. The ride quality is so much nicer compared to the garbage shocks the previous...

Scored a set of these Fox 3.0s. Easy weekend install, rides smooth and stable on road, cant wait to take them off road. Previous owner had a set of "radflow" 2.5 shocks upfront and blown rear stock shocks, I'm not familiar with that brand but it rode like trash to me. I also swapped out the IWEs...

Any recommendations on valve springs?

Corsa xtreme on my last gen 1, loved it. My new gen 1 came with a Roush with a downturn exit. I'm looking to go back to a corsa. The Roush sounds good but has more drone when the corsa xtreme at highway speeds.

When I bought 2nd gen 1 recently the ac never felt cold in the cab, but cold at the vent, especially in the Houston heat, the flow at the vent wasn't as strong much as my previous 14'. I replaced the recirc vent flap and actuator under the passenger side, (not easy with dash in the car). The ac...

Fuse 12 in the passenger kick panel. I had a similar issue on this new gen 1 I picked up where the puddle, cargo and interior lights did not work. No bad bulbs, wires, or faults. Ended up being the previous owner had the vehicle in "dark mode" via forscan. It is also possible it may be a bad...

https://www.diodedynamics.com/store/catalog/product/view/id/22470/s/2010-2014-ford-svt-raptor-dome-light-led/category/1453/ https://www.diodedynamics.com/store/catalog/product/view/id/22469/s/2010-2014-ford-svt-raptor-map-light-leds-pair/category/1453/...

2014, interior lights were replaced with diode dynamic leds, the ambient lights are OPT7 Aura Smart-Color LED Strip Interior Lighting Kit from amazon. The camera did make them all look a little brighter than they really are, but the DD leds are quite bright.

Never had any issues with Diode Dymanics, used them in my last few vehicles. Not the cheapest option, but consistent.

ebay 200$ range

Sold Sold

Yes you will need a tune to remove the check engine light. Other then that sounds like your pretty set given you already have the intake and exhaust setup. Get ready for the sweet smell of exhaust. Personally I'd just get a set of catless headers and a tune or high flow cats, as last time I went...

How secure is it? I'd like something like that for my AR if it's secure enough.

Keeps vibrations down in frame from what I'm told.

Dealers always seem to offer up free scratches when possible. I think those beadlockers just off too much additional trouble, though they do look nice. I'd tell the service manager to make it right, there's no reason for such carelessness.

Look what was waiting for me today, apparently I had a tiny rock chip near the cowl, and with Houston's smoldering weather today it cracked 12+ inches. Any suggestions for glass replacement in West Houston? Dealer, safelite, alternative?

I'm not a fan of the new raptors but that does look great. Makes it actually look different than the rest of the f150 line up.

Best bet is to use a relay harness and trigger it by the upfitter switch. Otherwise your asking for trouble. Since the wiring is fairly small gauge, you would have to replace the wiring in the circuit, upgrade fuses, I don't remember what their relays were rated for, but those might need...

Sadly no, maybe one day you can choose mapping app for carplay. I prefer waze.

Doesn't look repairable. I'd rewrap it, if your doing it yourself, go slow and have a hair dryer handy to loosen the film.

According to the specs online there is a 1 1/4in difference between the rigid and BD, with the BD being 20in, and the rigid being 21 1/4in. Using the rigid mount, you might be able to add spacers between the ends of the BD led bar and the bracket to make up any difference. I did something...