Search results

Hey folks, Let’s make a Dragy Repository. Post up your dragy times with pic or it didn’t happen. With your dragy, post your mods, your tune, your conditions like weather, humidity, road conditions and anything else you think is relevant. I think it could be really helpful to have a...

I found this to be a very well written article on the way the ecoboost operates. It is written in layman’s terms for the mechanically inclined amateur and assumed limited prior knowledge. It’s a good primer for understanding what is happening under your hood...

Afternoon, I created a new thread because the old one doesn’t do it justice. As many of you are aware, I was disappointed with my previous tune and build. AFE intake, WHIPPLE intercooler, AMS intake tubes, CRP stage 4 turbos, CRP manifolds, Kooks Downpipes, 170 degree thermostat. I came...

Disclaimer: Please know that I wasn’t looking to point fingers or put down any products... I see where this thread has bounced around and I was bummed a little. AdmittedlyI was disappointed in the results but it doesn’t mean that this wouldn’t be a reasonable upgrade for some people, knowing up...

So as part of finishing my build... I had installed Foutz skid plates and then I used RCI for the gas tank. my truck is still in the shop. For those with foutz or Ford performance... how do you change the oil? Does that middle skid plate come off easily? Just want to know what to expect!

Check this out...

couldn’t resist!

13” 1080P screen. Same processor and such as the last generation but a nice step up in resolution! https://phoenixautomotiveinc.com/products/px6-six-core-13-android-9-fast-boot-navi-radio-for-ford-f-150-2015-2019?_pos=7&_sid=511593d9f&_ss=r

Nice quality. The skids are smaller than stock. I’ll keep the gas tank skid but the rest is going back. This would be better suited for an F150 platinum or something. Im going to go with Ford Performance since it covers as much as the factory OEM.

I don’t just want to pry them off, even though I suspect they are just clips. I also don’t want to take down the front fender liners to verify if someone else has already done this maneuver. how do you get off the side vents to change them? Anyone?

The title says it all. I’m doing a bit of an overhaul of my truck. One of the things I noticed, living in the NE is that I have some surface rust on the under belly skids. I want to go aluminum. RCI metalworks and Foutz are my top contenders. Anyone have either and can comment? Foutz...

This is a repost from the GEN 2 forum. Should apply to all of you too. And I suspect it’ll work with other brands as well. Maybe this is common knowledge... not sure.... but I installed my new powertrax electric tonneau cover... and I was annoyed that I didn’t have an in truck solution for...

Maybe this is common knowledge... not sure.... but I installed my new powertrax electric tonneau cover... and I was annoyed that I didn’t have an in truck solution for a switch. then I started thinking about how I could hack it to make it possible. To do so I knew I would need to clone the...

I have a strange noise I’ve noticed on my truck lately. when I slow down, coast to a stop, I detect a grinding noise. I did power stop pads and rotors a month back but I don’t think the two are related. the noise is not present when the truck is slid into neutral while coasting. I Pulled...

I agree it’s time for a new thread. Some key new features. Voice commands! You heard me right. New modern hardware that runs the tablet with the modern speed and fluidity you’d expect. 360 Camera button working as expected. Updated Bluetooth 5. New microphone for cleaner Bluetooth calls...

ok... So I own this one. I was changing out my px3 tablet radio for a px6 tablet radio. Fooling around I decided to pull apart the dash again... And I broke my own rule and plugged in connectors for HVAC, sync 3, and the three dash buttons for camera and hazards etc... with the ignition...

whats your ride height like vs stock with blocks? I’m finally getting around to having my guy install mine. Are they exactly OEM height or a little higher or lower?

I started a new thread for the DIY INSTALL. It’s already over. I pulled the factory sync 3 out of the dash This morning. There are 4 7mm bolts to remove. Two by the speaker and two underneath the top panel once you pop the clips. The front bezel then pops off. There are six 7mm bolts to...

so 22k Miles The idler pulley squeals like a pig when the temperature drops. WD40 quiets her down but only lasts a few days. I’m planning on replacing the pulley and probably the belt while I’m at it. Anyone know of any aftermarket pulleys that are superior to the OEM? Anyone else have a...

Anyone run these? I’m not looking for a $2000.00 Fox kit. A little extra security would be nice. Wondering how these compare to stock. They’re cheap enough...

hey folks, I busted out my FORScan again because I wanted to disable the double honk, the seatbelt reminder chimes, and the annoying 3 chime every time you get in and start up. I had no trouble editing the as-built data for the above mentioned mods and they worked! But my sync radio went...

So... This has been a journey. I started out with the DIY under $500.00. Then as a project I wanted to tackle something a little more challenging and involved. I also wanted to try out some different components along the way. We all know that Focal is tried and true and proven. Dom...

I wanted to share. Phoenix Android Audio has a new 12.1 inch tablet screen coming out that will replace the factory screen but not the sync 3 brain. It retains hardware ac controls as well as ALL of the original sync features including the voice commands and remote start by ford pass...

So I loaded up some Toyo’s on a beautiful black ICON rim. Customwheels4u gets it done. The pros Looks awesome... pictures don’t do them justice. The RT handle great. The performance handling is superior to the stock BFG. The sidewalls flex less and the truck is planted more firmly when...

Hey Guys, I have 5 Holeshot xd129 rims that I need to unload. The spare has 100 percent stock KO2 tread The other 4.... have 22,000 miles of burnouts on them. The rims are in mint condition. I’ll include the black lugs. You “could” run them another 5-10k miles if you don’t live in a snowy...