Search results

Gen 1's are 26....seems odd they would change.

I was having issues, but it was the transfer case shift motor that would not stay engaged.

I agree with what was posted above. My guess is that if you pull full of water you will easily exceed 800lbs on the tongue with a trailer of that size. My 19' Lance is around 550 lbs on the tongue and 3500lbs on the single axle. My recommendation is to have the RS dealer install the...

I know this is an ancient thread, but I figured I would state that my Source CO2 tank came with one of these beverage handles on it (snap ring). I had to take about 1/4 inch off of it in order for it to fit under the bakflip. It does allow the 10 lb tank to sit vertically in the bed now though.

Been working on a very simplistic bed system. Just attached a piece of unistrut with some reinforced corner brackets to the front tie downs. Was able to attach some rotopax stuff to it along with my co2. I have 2x 3 gallon gas and 2x 2 gallon water and my 15lb co2. Plan to put some TREDs on...

My wife decided to park a little crooked in the garage and destroyed my right rear flare (passenger), anyone have a take off? Ford wants a ton for these things.

Greg, this doesn't make much sense to me. If one wheel is spinning faster, the Torsen will begin to engage without any electronics. What you are describing with the brakes being applied by the traction control is how vehicles without a mechanical means of a limited slip can control wheel spin...

Any information on: 96L WHEEL LINER*ACC 180 Are these actually liners or linex? ===================================== I would guess Plastic?? Because it shows *ACC (shipped to parts dept?? for install @ dealer) But 2013 Order Guide just shows New for 2013 • Exterior — HID...

Just got back a week ago from a two week trip with the trailer. Had a lot of fun tooling around Oregon with it. I'll use the "Elk Power" photo as my entry this month, enjoy! Here is the one I call..."411hp meet 20ep (elk power)" I can't use these since I've posted them on...

this is my entery Ok, went out over the weekend and took a few pics. Not sure which one I want yet, I may even go out and get some more in the next week. Hope you enjoy...

Thanks for the comments guys. I'll have to get some photos of the interior up sometime. I'm thinking they probably will not put that in the magazine since the last one rolled off the production line in late 2008 or early 2009. They only made about 300 of them, so they are pretty rare...

Some of you may have seen my other thread where I posted my ML55 towing my Airstream Basecamp, but I figured I'd better get some photos of the Raptor towing it now. I took these photos just north of Pacific City, OR. This was the second trip towing the trailer with the Raptor. I have to...

Got the truck back from the dealer and they did a great job adjusting the door. It still isn't quite as tight as the driver door, but very close. A little surgical tube upgrade in the weather stripping and I will be good to go.

Ok, first attempt at this. Just got the truck 3 weeks ago and was out on the beach over the weekend. This is the Peter Iredale in Fort Stevens State Park, it ran ashore near the mouth of the Columbia River in Oregon in 1906 and has been there ever since. This was a very impromptu picture and...

Ok, took some pics before I headed off to the dealer tonight. The dealer is going to adjust the door tomorrow for me. I went and looked at another Raptor that they had on the lot and it seemed like it had a similar issue, along with an FX4, however it was slightly less severe then mine. In...

So I noticed a thread on here about a week ago talking about the violent shaking of the passenger door. Just a day prior to that, my wife commented on it and I thought nothing of it. Well yesterday, driving down the highway, my wife puts her fingers between the door and the cab and presses on...

142mph? Really? Pretty sure that is just crazy on stock tires.

McKenzie Ford has 4 coming in soon you can see them on Autotrader already, did none of them match what you ordered? Just take a look on Autotrader and get the VIN's and paste it at the end of this link: http://www.inventory.ford.com/services/inventory/WindowSticker.pdf?vin= Or maybe you...

Welcome, also another Oregon member.

So something worked. Just got a build week of Feb 27th. Figuring I will finally see the truck around March 21st, 140 days.

Ok, figured I'd chime in here. Ordered on Nov. 4th and didn't really hear anything for a long time. About a week and a half ago I talked with the dealer again and they stated they didn't know any more information and gave me the regional manager contant information. I called her and really...

Wow, shocked at all the negative reactions to a top. Obviously most of you live in fair weather and don't have to deal with rain/snow for over 1/2 the year. I know here in the NW there are a lot of trucks with tops on them. I'm pretty sure I will get one to transport the dogs easier and too...

Glad to see an OR Raptor w/ a VIN and Build date (besides the couple that have been on the lots around here), about time. I ordered early Nov and it looks like you ordered on Oct. 12th, so I'm hoping I will get a build date sometime early Feb and take delivery before March. Pretty sure...

Pm sent

Thanks for the compliments on the trailer. I was thinking about getting something that would be a little more rugged that I could pull around offroad. Probably something like a homemade teardrop. That Kimberly Karavan is pretty nice. As far as the Basecamp goes, it is definitely not an...