Search results

Get the PDP Mudflaps, unless you just want new wheels. They make a HUGE difference.

The only way you will be able to adjust from 20 hp to 200hp is by varying boost pressure. They only things that can do that with the push of a button are turbos, or that procharger. The positive displacement blower is a very good option for these trucks because of one main thing, torque...

I have 325s on methods. They used to rub at full lock until I had the suspension adjusted. The Methods stick out a little more so I think stock wheels would help. They also rub the inner fender a full bump, again I think a stock wheel might bring things inward enough to avoid any issues No...

Check out Dirty Deeds, I got one used here and it's pretty good. No drone with the special tube on it. Sounds awesome. I installed myself in the driveway. Put a ramp under passenger front and driver rear to flex the suspension to make room. Stocker goes out forward with a clockwise spin to...

Craig's list and eBay have them frequently

Dang, I have been wanting to try E85 for a while here, but I am too far away.

They have a phone, you have a phone, make it happen.

borrow a set from some body, beer talks

I went full monty on this little project. I put about 1/4" of expoy in the holes, wasn't sure how long the screw was. I then ran some silicone around the inside edge where the gray pastic meets the clear, you can see the gap in there. Then when I installed it I put a small bead under...

I saw a post about this else where. So I poured some clear expoxy into the bottom of the holes to beef things up a bit. I also plan to fill the screw hole with silicone after install.

Best, easiest, and cheapest mod out there! Truck stays so much cleaner

$284 on Amazon, free shipping

Just pulled the trigger on a new 3rd brake light. I did some searching here but couldn't find any threads about how to seal a new brake light to keep the water out. Anybody got a good strategy on getting it sealed and keeping it sealed up? Really don't want to buy another if I don't...

Power steering cooler while you have it apart

Couldn't a lock Smith do it?

Mine did this once a year ago. Basically the flap that closes the end of the cylinder wouldn't open. Did a quick search and found that it's semi rare for these trucks. There are 2 options. A, replace or B use force to get the key in. I forced mine with a screwdriver and got going. Mine...

There is a set on Nashville, TN craiglist. Not mine, just saw them

I don't have any personal experience with the SC but generally the tunes don't touch the Off Road Mode setting changes. Basically the tune you put in for the SC engine is there and the Off Road Mode changes things like shift points and throttle response things. If you are near Indianapolis...

Look in the general section and read the thread about RCVs on a daily. Cliff notes, don't, as it seems to hurt the bearings more. But read and form your own opinion

One of the other videos said Stainless Works headers with cats and a Borla cat back. Sound pretty rowdy!

I could do Saturday, let me know.

Ended up rolling solo here but it was still a good time! Made a bunch of climbs in the dunes area and some more techinical onces the back dunes area. Found my way back to the quarry area, I wussed out on the tough way in but got in anyway. Made a pretty tight climb in the quarry, it took...

sweet, does the timing look good for you?

Cabs are the same so it should fit. Side note, be prepared for some wind noise with the light mounted there. If your truck is loud ( exhaust and MT tires) you probably won't notice much, but if its pretty stock you are going to hear it.

Alright, you have got to love family, but I no longer have a commitment on the 4th! Lets go offroad! Lets meet at 10am at County Market 109 W Jackson St, Attica, IN 47918 (765) 762-2337 https://goo.gl/maps/ptVTNhPYwcC2 Larger parking lot and a gas station there, McDonalds across the street...