Baofeng or ETekCity UV-5R programming instructions

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Trick.Raptor

The Cracker Raptor
Joined
Nov 7, 2014
Posts
3,966
Reaction score
7,737
Location
Santa Maria, CA
So messing around I didn't a factory reset on the handled UV-5RA. I couldn't load your file into the radio and had to clone the radio and copy some of yours over to make sure it works and it does.

Question I have is I can get the top (A) to show like WXMAN, but (B) only shows the frequency number like 151.625. I can't seem to figure it out to show the text, but the freq is programmed and shows mirrored locations such as the group A. Any thoughts? I tried having the arrow showing B active before start the download, but no luck. Any help would be great and the file you have with all of the freq's gives me the error due to firmware. Any way you could try a new clone of your radio? You could email the file to me and see if it works.

I have an issue with top (A) and bottom (B). WXMAN will show in A and the correct frequency in B. However If I change (A) to another name the frequency stays the same. I can't seem to make them both change at the same time...
 

ISFast

FRF Addict
Joined
Mar 11, 2011
Posts
2,557
Reaction score
965
Location
Tulsa, OK
I have an issue with top (A) and bottom (B). WXMAN will show in A and the correct frequency in B. However If I change (A) to another name the frequency stays the same. I can't seem to make them both change at the same time...

They are so you can flip back and forth easily (A/B blue button) on two different frequencies. They are independent of each other. An arrow will be to the left so you can tell which one you are keyed up on/ monitoring.
 

Trick.Raptor

The Cracker Raptor
Joined
Nov 7, 2014
Posts
3,966
Reaction score
7,737
Location
Santa Maria, CA
They are so you can flip back and forth easily (A/B blue button) on two different frequencies. They are independent of each other. An arrow will be to the left so you can tell which one you are keyed up on/ monitoring.

OK... good to know. I thought I had to make it so they both matched. Everything else seemed to be OK.

I did download @Slacker to make sure I had the correct settings. After a few adjustments everything is good.

THANKS!!
 

ISFast

FRF Addict
Joined
Mar 11, 2011
Posts
2,557
Reaction score
965
Location
Tulsa, OK
OK... good to know. I thought I had to make it so they both matched. Everything else seemed to be OK.

I did download @Slacker to make sure I had the correct settings. After a few adjustments everything is good.

THANKS!!

Very Nice! I got some help and all are programmed like originally when I bought it from Trey during the very first or second TRR.
 

Mluis11

Full Access Member
Joined
Jan 29, 2015
Posts
998
Reaction score
1,476
So messing around I didn't a factory reset on the handled UV-5RA. I couldn't load your file into the radio and had to clone the radio and copy some of yours over to make sure it works and it does.

Question I have is I can get the top (A) to show like WXMAN, but (B) only shows the frequency number like 151.625. I can't seem to figure it out to show the text, but the freq is programmed and shows mirrored locations such as the group A. Any thoughts? I tried having the arrow showing B active before start the download, but no luck. Any help would be great and the file you have with all of the freq's gives me the error due to firmware. Any way you could try a new clone of your radio? You could email the file to me and see if it works.


I'm guessing you know how to change the display option from freq/name/ch in the menu for A or B independently. Are you saying when you do that the name info isn't there?
 

Trick.Raptor

The Cracker Raptor
Joined
Nov 7, 2014
Posts
3,966
Reaction score
7,737
Location
Santa Maria, CA
I'm guessing you know how to change the display option from freq/name/ch in the menu for A or B independently. Are you saying when you do that the name info isn't there?

I figured it all out and while the setup I did for you works, there is room for improvement. I'll send you a text.
 

Mluis11

Full Access Member
Joined
Jan 29, 2015
Posts
998
Reaction score
1,476
How about I just send you my radio[emoji12] sounds good. Looks like I'll have a free day Monday and/or Tuesday FYI
 

breed

Member
Joined
Aug 19, 2018
Posts
16
Reaction score
4
This was a hugely valuable thread, and thanks so much for the info.

I recently bought a Baofeng UV-82HP off of Amazon (https://www.amazon.com/gp/product/B00Z52HP10/?tag=fordraptorforum-20), as well as USB Cable (https://www.amazon.com/gp/product/B00HUB0ONK/?tag=fordraptorforum-20) and a stronger Antenna (https://www.amazon.com/gp/product/B00KC4PWQQ/?tag=fordraptorforum-20).


I struggled with the base image file to upload, since the firmware on the UV-82HP is different than the UV-5.

What I did was the following:

1. Using CHIRP, I went to Radio --> Download from Radio and backed up my stock radio image (File -- Save As)
2. I opened the IMG at post #1 of the thread, then I went to File Export and exported the channels as a CSV.
3. I opened my radio image from #1, then went to File --> Import and imported the CSV to my radio image in CHIRP.
4. Save that new file with a new name (just to be safe).
5. Go to Radio --> Upload to Radio

Check that your channels are on your new radio. Hope this helps someone else.





Baofeng UV-82HP 1.png
 
Top