Eibach Pro-lift springs installed with pics and comments

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

CHMP

Full Access Member
Joined
May 28, 2019
Posts
274
Reaction score
143
Location
Santa Cruz
Out of curiosity, why are you going to drive it 200 miles before getting the alignment? Wouldn’t you want it done ASAP?

From what I've heard it's good to drive around for a while and let things settle before shelling out the cash for a proper alignment. Honestly though if you follow the rules and get an alignment/balance/rotation every 5k it probably won't matter.
 

Kyle Nezat

Full Access Member
Joined
Oct 25, 2019
Posts
144
Reaction score
25
Location
Louisiana
Out of curiosity, why are you going to drive it 200 miles before getting the alignment? Wouldn’t you want it done ASAP?
In my past experiences the allignment isn’t off that much so I like to drive it a while and beat on it to get everything to settle back in and let the springs break in then do a re torque then allignment. I have don’t lift kits and don’t tape measure and level allignments and truck drove good. Also do want to get the allignment cams before I bring it in
 

Kyle Nezat

Full Access Member
Joined
Oct 25, 2019
Posts
144
Reaction score
25
Location
Louisiana
Mine was 1/4" nose high on the pside, 1/2" dside initially. I'm a little over 1000 since the swap now, I'm almost level but not quite. Honestly feel like it will settle to dead level when I get to 5000 miles. Word of advice, get ready to install this camber kit to be able to dial to Eibachs recommended camber of -.4:

https://www.4wheelparts.com/p/specialty-products-camber-bracket-kit-86250/_/R-FCMW-86250

My alignment shop was able to get it right on the dside, but -.6 is the best they could do on the pside without that camber kit.
That’s good to know thanks buddy
 

Ski4Ever

Full Access Member
Joined
Jan 23, 2019
Posts
501
Reaction score
166
Location
Denver, CO
Mine was 1/4" nose high on the pside, 1/2" dside initially. I'm a little over 1000 since the swap now, I'm almost level but not quite. Honestly feel like it will settle to dead level when I get to 5000 miles. Word of advice, get ready to install this camber kit to be able to dial to Eibachs recommended camber of -.4:

https://www.4wheelparts.com/p/specialty-products-camber-bracket-kit-86250/_/R-FCMW-86250

My alignment shop was able to get it right on the dside, but -.6 is the best they could do on the pside without that camber kit.
Rather than buying from 4WP, I'd recommend purchasing from one of our local resellers here on FT. I bought mine from @NEOGARAGE recently. His price is better than 4WP, no tax (depending on what state you're in, I think), and fast/free shipping!
 

Kyle Nezat

Full Access Member
Joined
Oct 25, 2019
Posts
144
Reaction score
25
Location
Louisiana
So happy with the ride of the eibachs however I for sure need to get the rear up a little. What have y’all been doing to the rear?
 

Nick@Apollo-Optics

Supporting Vendor
Supporting Vendor
Joined
Apr 3, 2011
Posts
7,391
Reaction score
3,055
Location
Houston, TX
So happy with the ride of the eibachs however I for sure need to get the rear up a little. What have y’all been doing to the rear?

Most folks do springs. But some folks just go with blocks. With blocks, you’ll only get the height increase. With springs, you’ll get the height increase, more comfort, less axle wrap, and added overall performance. The only drawback is more sag when towing.
 

Slow6

Full Access Member
Joined
Nov 13, 2017
Posts
476
Reaction score
198
Location
AK
Most folks do springs. But some folks just go with blocks. With blocks, you’ll only get the height increase. With springs, you’ll get the height increase, more comfort, less axle wrap, and added overall performance. The only drawback is more sag when towing.
Are you saying towing capacity is reduced with after market springs?


Sent from my iPhone using Tapatalk
 
Top