GEN 2 Baja Designs S2 back up lights install

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

TimmyP

Active Member
Joined
Nov 24, 2018
Posts
68
Reaction score
125
Location
Cypress, TX.
I mounted mine in the bumper as well. I just didn't like the look of the S2 right next to the exhaust ( I don't think it would affect it, just didn't care for the look as much) I got the wiring from Rick @ Freedom but the spacing on the lights didn't allow the jumper to work. I just made my own harness and then ran the main harness through the frame rail I then hooked up to SW4. I didn't want mine to automatically come on so it made wiring even easier.

iwPazbOkSiKpeH8CZxcTnw.jpg
 

FordPerf Addict

FRF Addict
Joined
Aug 24, 2016
Posts
1,321
Reaction score
521
The entire light? Not sure I need a new one but I’ll ask


.
I sent it back and they tried to remove the screw themselves, and they ended up sending me a new light because they had no way of getting it out


Sent from my iPhone using Tapatalk
 

Slow6

Full Access Member
Joined
Nov 13, 2017
Posts
476
Reaction score
198
Location
AK
I mounted mine in the bumper as well. I just didn't like the look of the S2 right next to the exhaust ( I don't think it would affect it, just didn't care for the look as much) I got the wiring from Rick @ Freedom but the spacing on the lights didn't allow the jumper to work. I just made my own harness and then ran the main harness through the frame rail I then hooked up to SW4. I didn't want mine to automatically come on so it made wiring even easier.

View attachment 121862
Moving mine into the rear bumper as you did, just waiting for the bezel pieces. I’m not near my truck currently, is it possible to mount them further to the outside at all? Or is there not enough of a flat spot to make it look good?


Sent from my iPhone using Tapatalk
 

TimmyP

Active Member
Joined
Nov 24, 2018
Posts
68
Reaction score
125
Location
Cypress, TX.
I think it would be hard to move further outboard. I'll check and get back. I've seen them closer at an angle, but I didn't like that look either. the biggest problem is bezel size and fitting flush on the bumper.

Moving mine into the rear bumper as you did, just waiting for the bezel pieces. I’m not near my truck currently, is it possible to mount them further to the outside at all? Or is there not enough of a flat spot to make it look good?


Sent from my iPhone using Tapatalk
 

Slow6

Full Access Member
Joined
Nov 13, 2017
Posts
476
Reaction score
198
Location
AK
I think it would be hard to move further outboard. I'll check and get back. I've seen them closer at an angle, but I didn't like that look either. the biggest problem is bezel size and fitting flush on the bumper.
I didn’t care for the angled look either. Light wouldn’t go where I want it.


Sent from my iPhone using Tapatalk
 

Winchester30

FRF Addict
Joined
Oct 4, 2018
Posts
1,416
Reaction score
4,387
Location
WI
Not sure if it does, just following manufacturer’s directions.
Bracket, spacer, then truck.
 
OP
OP
halogrinder

halogrinder

Full Access Member
Joined
Jun 18, 2017
Posts
142
Reaction score
114
this was before anything was available and (probably) based on this write up lol.
This works perfectly fine. if you put it on the other side, you have to run a spacer due to the bend in the lip on the bracket.
 
Top