GEN 1 Whipple Kit Install :D

bsimms89 · Feb 5, 2019

I don’t see any heater hoses behind the supercharger, just the one under the supercharger behind the alternator which is the new inlet/barb that was installed, I have it’s location circled on here, the two heater lines run back into the firewall to the heater core and those are dry

MTF · Feb 5, 2019

Shit that sucks, hope you figure it out.

Dalamar · Feb 5, 2019

MTF said:
I just notice you didn't add a oil catch can on the passenger side.
I recommend it, the PCV goes straight into the front of the compressor,
so the oil and crap will coat the twin screws and the intercooler.

View attachment 118571

This was taken in 2015 about 3 1/2 years worth mostly in the winter months when they switch to shit winter gas.

View attachment 118572

Wow, That's good to know. you'd think they would recommend it with the kit?
Thanks man.

Dalamar · Feb 5, 2019

bsimms89 said:
I just started mine up yesterday on the lift with my new tune from JDM, it idles smooth and A/F ratios are all good, trying to find a mystery coolant leak tho. Its coming down from the back of the motor from what looks like inside the bellhousing, then dripping out where the oil pan meets the block near the starter. above and around the starter is dry. At first I though it was the rear hoses into the intercooler but they are dry, and if I turn the key on but dont start the motor to let the intercooler pump run it doesn,'t leak, only leaks when the motor is running which should tell me it's the engine's coolant. Trying to find where it could be coming from.

Congrads on the startup!
Bummer on the leak, I'm sure you'll get it handled.

Mine sounded good on startup with the exhaust and the little whine.

Dalamar · Feb 5, 2019

Any recommendations on where to get the oil blow-off can?

1BAD454SSv2 · Feb 5, 2019

sorry man, I should of said behind alternator/under blower. Did you use the spring clamps?

BenBB · Feb 5, 2019

Dalamar said:
Any recommendations on where to get the oil blow-off can?

Summit or https://www.rdpstore.com/p-6105-mor...rators-universal-small-body-clear-bottom.aspx

Gary E · Feb 5, 2019

Dalamar said:
View attachment 118587 View attachment 118588

Any recommendations on where to get the oil blow-off can?

I'm using JLT breather catch cans.

MTF · Feb 5, 2019

This is the one I bought.
https://www.moroso.com/air-oil-separator-kit-large-body85492/

I bought this one for the drivers side, turns out I didn't need one for my truck.
Well, us Whippled guys don't need it.
We have enough vacuum on the passenger side that the drivers side works the way it is meant to work, sucks in fresh air.

I may take the clear one off and put it on the passenger side. I like the idea of seeing it.
https://www.moroso.com/air-oil-separator-universal-kit-small-body85682/

bsimms89 · Feb 6, 2019

1BAD454SSv2 said:
sorry man, I should of said behind alternator/under blower. Did you use the spring clamps?

Yes I just reused the factory clamp, I just ordered some breeze worm gear hose clamps, going to have to take the blower and alternator back off to change the clamp. Hoping it’s leaking from the hose on the barb, and not where the new barb goes into the block. Don’t know how I’d fix it if that were the case and I can’t be sure which it is by looking at it

GEN 1 Whipple Kit Install :D

bsimms89

Active Member

MTF

FRF Addict

Dalamar

Full Access Member

Dalamar

Full Access Member

Dalamar

Full Access Member

1BAD454SSv2

FRF Addict

BenBB

FRF Supporting Member

Gary E

Full Access Member

MTF

FRF Addict

bsimms89

Active Member

Similar threads

Staff online

Members online

Forum statistics

Latest posts