Recent content by TurboTim

  1. T

    Selling 2020 17" Cast Aluminum Wheels

    I know it's a long shot but I only need one. Just need a spare. I'm in DFW as well. Sent from my SM-G975U using Tapatalk
  2. T

    2014 f150 lariat raptor conversion help

    Just buy a raptor dude. Your looking at front and rear shocks, upper and lower control arms, tie rods, CV axles, rear axle, leaf springs, spindles, longer brake lines, fenders, bedsides. Also going to need 35s and new wheels because even regular f150 wheels in a 17 inch are a different offset...
  3. T

    GEN 1 Squeak on Deavers

    White lithium grease is what deaver recommended to me. No more squeaks. Been a year without them! Sent from my SM-G975U using Tapatalk
  4. T

    ICON UCA on Gen 1

    It wouldn't rub if u aired down. The part of the tire that gets wider when you air down is the portion of the tire that comes into contact with the ground. If your really worried about it throw some 1/4 inch spacers on the front. That's what I did. Theyre small enough to not cause any issues. I...
  5. T

    Fox 3.0 Factory Series ?

    Get the 3.0s! They're awesome! Whenever I hear them it makes me smile. Makes me realize that my shit is legit. Don't listen to the nonsense from people who complain about the noise! You don't complain when your bed squeaks while banging! just get them. I think the ride is better on road. My...
  6. T

    GEN 1 37s, stock wheels, mid perch?

    The ko2 is 36.5 inches in diameter. Here are all the other specs: BFGoodrich All-Terrain T/A KO2 37X12.50R17 https://tiresize.com/tires/BFGoodrich/All-Terrain-TA-KO2-37X12.50R17.htm Sent from my SM-G975U using Tapatalk
  7. T

    free subwoofers and pedal commander

    423 Sent from my SM-G975U using Tapatalk
  8. T

    GEN 1 FOX 3.0 front install

    Who did you buy them from? Most the time they mimic the same amount of lift you get from mod perch. Sent from my SM-G975U using Tapatalk
  9. T

    GEN 1 37’s: Fiberwerx alone get you there?

    The stock wheels are most ideal offset for running 37s. In this photo, the way the wheel is turned is where you'll have issues with the firewall on more offset wheels. With my stock wheels it clears fine. Sent from my SM-G975U using Tapatalk
  10. T

    GEN 1 FOX 3.0 front install

    You can only adjust the height once installed. There is a spanner wrench that you need and its actually way easier to do when the shocks are already mounted. If you are going to adjust them, do it the first time u install them because any significant height change will require another alignment...
  11. T

    GEN 1 37’s: Fiberwerx alone get you there?

    Also, you need to be at least on mid perch. And for what its worth, I am running 37x12.50R17 BFG KM3s. I never even did the pinch weld. Unnecessary. It is a little bit scary the first time off roading hard with the 37s but then you will quickly realize its all good. Now if you were running...
  12. T

    GEN 1 37’s: Fiberwerx alone get you there?

    If you have stock wheels with 37s and stock fenders you don't need to do anything else. Yes, I know everyone says they trim a ton well i didn't trim anything and I send it very hard off road. I have jumped it and fully compressed without issue. The only thing is when you fully compress you cant...
  13. T

    GEN 1 FOX 3.0 front install

    They should come pre set to level ride height. Expect them to settle about 1/4 inch after some driving. Not a whole lot to the install. Lot of people loosen the axle nut, but I never do. But do make sure you disconnect the sway bar to get more droop. There are a ton of YouTube videos on it. I...
  14. T

    What did u do to your raptor today?

    Got an MBRP turndown exhaust installed, no resonator. Put a little video together of a hot ass cold start and some acceleration. Sounds 5,000 time better in person Watch "MBRP Turndown Exhaust Raptor" on YouTube Sent from my SM-G975U using Tapatalk
  15. T

    Sold-MBRP 3.5” Installer Series with Dump

    I'll take it. Sending message now. Sent from my SM-G975U using Tapatalk
Top