Phoenix Android Audio retains Sync 3

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

rsbug

Full Access Member
Joined
May 28, 2018
Posts
218
Reaction score
65
Location
N Texas
So I pulled the dash back out to fiddle around.

So what do you guys think I did? I’m not seeing an obvious fuse blown. I grabbed the diagram for the lock panel and under the hood.

Did I fry the Bodycontrolmodule?

I'm no mechanic, but looking through the maintenance manual for my truck ('18 Raptor, 802a), I think you hit the nail on the head with the BCM being responsible for those malfunctions.
Fuse location 4 (60A) is for the BCM
Fuse location 25 (50A) is for BCM 1
Fuse location 41 (30A) is for BCM voltage quality module feed
Fuse location 76 (40A) is for BCM 2

You've probably looked into these, but figured I'd pass it along
Hope you're able to resolve it
 
OP
OP
G

Guy

FRF Supporting Member
Supporting Member
Joined
Feb 16, 2017
Posts
1,781
Reaction score
1,122
That’s why I dumped it the dealer. I think the BCM is gone.... which means it needs a new one and they have to use FORD IDS to program it.
 
OP
OP
G

Guy

FRF Supporting Member
Supporting Member
Joined
Feb 16, 2017
Posts
1,781
Reaction score
1,122
It still may be a push fuse. The relay would click when the ignition key button was switched to on. So it’s something beyond the kick panel fuse box I think.

Bcm is still possible... I’m just really surprised that plugging in connectors with the power on is enough to take out a control module. I didn’t see that coming.
 

rsbug

Full Access Member
Joined
May 28, 2018
Posts
218
Reaction score
65
Location
N Texas
Wouldn’t think anything you were doing in that location would cause a 30A fuse to blow without some sparks flying around. Sounds like an anomaly for sure.
 
OP
OP
G

Guy

FRF Supporting Member
Supporting Member
Joined
Feb 16, 2017
Posts
1,781
Reaction score
1,122
It could be a lesser fuse still causing communication errors... but I think I have corrupted software on a major module if I had to guess. Like a windows 98 gone south with the blue screen. I used FORScan to reboot some of the bigger modules and it made no difference.

Wouldn’t think anything you were doing in that location would cause a 30A fuse to blow without some sparks flying around. Sounds like an anomaly for sure.
 
OP
OP
G

Guy

FRF Supporting Member
Supporting Member
Joined
Feb 16, 2017
Posts
1,781
Reaction score
1,122
Moral of the story.


Disconnect the battery terminal when doing radio work. Save yourself the headache. I took one for the team. Again.
 
OP
OP
G

Guy

FRF Supporting Member
Supporting Member
Joined
Feb 16, 2017
Posts
1,781
Reaction score
1,122
I couldn’t fix it with simple trouble shooting and so my skill set isn’t up to speed...

But I would think if the link from the battery to the fuse box went out.... the whole truck would be dead... I have power in some places inside the cab and the truck runs. The “electronics”,
Front windows and doors, locks... are dead.

I haven’t had the best luck with this local dealership but I didn’t feel like towing it a half hour to the next one as I don’t think they are neccessarily any better!

I have plenty of other vehicles to drive.... so I’m whining, but really it’s a first world issue here and I should be grateful this isn’t the transportation I use to care for my family or earn a living or depend upon.
 
Top