Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Audio/Video/Electronics Forum [GEN 1]
V-1 Radar Detector
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="MagicMtnDan" data-source="post: 86062" data-attributes="member: 2768"><p>I can do that. I was involved in the thread on the other forum. Unfortunately I didn't make a copy of what I wrote (whodathunk it would have been necessary?!) so I'll have to re-create it as best I can. Note that Mark T and at least one other person provided information relating to the harnesses and the pin locations so credit and thanks must go to them.</p><p></p><p>There are two different connectors and harnesses made for the Raptor. One is for the Raptors with the backup camera - it has 16 wires in it - and one is for Raptors with SYNC and that one has 10 wires in it.</p><p></p><p>Pin 1 on both mirrors is switched 12v. The wire color is Blue with red stripe. The power to this pin stays on like the radio does until you open the door or wait ten minutes.</p><p></p><p>Pin 3 is ground on the 16 pin mirror and the color of that wire is Black with a purple stripe.</p><p></p><p>Pin 10 on the 10 pin mirror is the ground and the color is also Black with a purple (violet) stripe</p><p></p><p>With the plug disconnected and hanging down from the mirror, sitting in the truck looking forward at the holes in the "white" end that plugs into the back of the mirror with the clip on the bottom side: Pin 1 is on the far lower left onand Pin 3 is on the lower row 3rd hole from the left.</p><p></p><p>If you are holding the 10 pin harness in your hand looking at the holes with the clip at the bottom then the 12v is at the bottom left and the ground is at the top right. The colors were exactly as posted. Also, on the back of the harness it is labeled 1 and 10. </p><p></p><p>It's small but I saw it while looking at the colors of the wires. To get the harness out you push up on the bottom of the clip and wiggle it back and forth. </p><p></p><p>The yellow invisicord wire goes in pin1 on the back and the black wire goes in pin 10.</p><p></p><p>Note: I will come back to this thread when I have time and update and add information.</p></blockquote><p></p>
[QUOTE="MagicMtnDan, post: 86062, member: 2768"] I can do that. I was involved in the thread on the other forum. Unfortunately I didn't make a copy of what I wrote (whodathunk it would have been necessary?!) so I'll have to re-create it as best I can. Note that Mark T and at least one other person provided information relating to the harnesses and the pin locations so credit and thanks must go to them. There are two different connectors and harnesses made for the Raptor. One is for the Raptors with the backup camera - it has 16 wires in it - and one is for Raptors with SYNC and that one has 10 wires in it. Pin 1 on both mirrors is switched 12v. The wire color is Blue with red stripe. The power to this pin stays on like the radio does until you open the door or wait ten minutes. Pin 3 is ground on the 16 pin mirror and the color of that wire is Black with a purple stripe. Pin 10 on the 10 pin mirror is the ground and the color is also Black with a purple (violet) stripe With the plug disconnected and hanging down from the mirror, sitting in the truck looking forward at the holes in the "white" end that plugs into the back of the mirror with the clip on the bottom side: Pin 1 is on the far lower left onand Pin 3 is on the lower row 3rd hole from the left. If you are holding the 10 pin harness in your hand looking at the holes with the clip at the bottom then the 12v is at the bottom left and the ground is at the top right. The colors were exactly as posted. Also, on the back of the harness it is labeled 1 and 10. It's small but I saw it while looking at the colors of the wires. To get the harness out you push up on the bottom of the clip and wiggle it back and forth. The yellow invisicord wire goes in pin1 on the back and the black wire goes in pin 10. Note: I will come back to this thread when I have time and update and add information. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
tcm glx
p0verty
HookEm
GCATX
damaschke
George512
bjorn-dpc
drew5580
kevo_lo
Stonehide
elpechedepeche
GEN3LV
DougDimmadome
LambSVT
Nv Guy
philofab
24NoVARaptor
CessnaDriver
VJDWashington
soheilmos
MEIRONMAN207
rbrb
Littlefx4
GreenGoblin
ln13ln13
nikhsub1
Frogger22
monsterspartan
TAC71
Punkur67
Robertcrav
Psirus7
letsgetthisdone
bobbyph1
JD05
Badboy4fun_wa
tonythis
Raptor_arw
weldoid
Brad12
Butterz
jm77
shigman
Rednose
Arizona Free
BadWRP
steveo1103
AZ_Raptor
... and 2 more.
Forum statistics
Threads
93,202
Posts
1,955,928
Members
56,485
Latest member
bjorn-dpc
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Audio/Video/Electronics Forum [GEN 1]
V-1 Radar Detector
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top