Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford F-150 Raptor General Discussions [GEN 2]
Remi Raptor Build
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="JAndreF321" data-source="post: 1506879" data-attributes="member: 40327"><p>I started getting some stuff in and getting stuff done. </p><p></p><p>Husky Liners</p><p></p><p>[ATTACH=full]302496[/ATTACH]</p><p>[ATTACH=full]302497[/ATTACH]</p><p>[ATTACH=full]302498[/ATTACH]</p><p>[ATTACH=full]302499[/ATTACH]</p><p></p><p></p><p> I had decided to buy Weathertech and in the middle of the direct purchase I thought I’d check Stage3motorsports and find out if it was cheaper…The Weathertech were more expensive but the Husky Liners were on sale so I went with them. From the pictures the main difference was that the Weathertech covered an extra few inches under the front seats and also had full grip lines in the back. The difference didn’t bother me. They seem solid, though I may trim a bit in the front passenger. </p><p></p><p></p><p>Dog Ramp</p><p></p><p>[ATTACH=full]302500[/ATTACH]</p><p>[ATTACH=full]302501[/ATTACH]</p><p>[ATTACH=full]302502[/ATTACH]</p><p>[ATTACH=full]302503[/ATTACH]</p><p></p><p> I had a ramp that we were using for the tailgate and it is 6 ft long. The underside has 6 rivet nuts hammered into the moulding. I’m not sure why those nuts were there but I found that they were 8mm and I used them to secure two aluminum square poles. I needed heavy gauge metal for the platform so I had to use sheet steel and paint it. Everything got bolted down and I filled a gap with aluminum sheet metal and taped over everything with grip tape from Lowes. I used long bolts for hooks and was able to get it to work.</p><p></p><p> The rivet nuts farthest from the edge was taking the pressure and ended up pulling out so I drilled all the way through and secured it with larger bolts. The length was still too short, but will work with a supporting box on the bottom. I couldn’t go longer and get the setup to fit in the truck bed. </p><p></p><p></p><p>Eibach Springs</p><p></p><p>[ATTACH=full]302504[/ATTACH]</p><p></p><p> My springs arrived today, the Timbren bumpstops come Wednesday, and the bump stop pads arrive…sometime? Forged Off-Road hasn’t given me an update yet; I didn’t think they were made to order.</p></blockquote><p></p>
[QUOTE="JAndreF321, post: 1506879, member: 40327"] I started getting some stuff in and getting stuff done. Husky Liners [ATTACH=full]302496[/ATTACH] [ATTACH=full]302497[/ATTACH] [ATTACH=full]302498[/ATTACH] [ATTACH=full]302499[/ATTACH] I had decided to buy Weathertech and in the middle of the direct purchase I thought I’d check Stage3motorsports and find out if it was cheaper…The Weathertech were more expensive but the Husky Liners were on sale so I went with them. From the pictures the main difference was that the Weathertech covered an extra few inches under the front seats and also had full grip lines in the back. The difference didn’t bother me. They seem solid, though I may trim a bit in the front passenger. Dog Ramp [ATTACH=full]302500[/ATTACH] [ATTACH=full]302501[/ATTACH] [ATTACH=full]302502[/ATTACH] [ATTACH=full]302503[/ATTACH] I had a ramp that we were using for the tailgate and it is 6 ft long. The underside has 6 rivet nuts hammered into the moulding. I’m not sure why those nuts were there but I found that they were 8mm and I used them to secure two aluminum square poles. I needed heavy gauge metal for the platform so I had to use sheet steel and paint it. Everything got bolted down and I filled a gap with aluminum sheet metal and taped over everything with grip tape from Lowes. I used long bolts for hooks and was able to get it to work. The rivet nuts farthest from the edge was taking the pressure and ended up pulling out so I drilled all the way through and secured it with larger bolts. The length was still too short, but will work with a supporting box on the bottom. I couldn’t go longer and get the setup to fit in the truck bed. Eibach Springs [ATTACH=full]302504[/ATTACH] My springs arrived today, the Timbren bumpstops come Wednesday, and the bump stop pads arrive…sometime? Forged Off-Road hasn’t given me an update yet; I didn’t think they were made to order. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
brink
Hup
03Cobraraptor
BBLV
14 tuxblack raptor
Stingray23
MattyIce716
MacK88DO
nikhsub1
ToadSmasher2K1
mgbond12
SeasickLI
Jay_P
Drkknght
Latchkey Kid
lawtonmc
wonka
EastEndAngler
Oldfart
Johnny Raptor
RaptorFan1988
bboz225
DrakeZiggy
Dnpbakon
j0eycantrell
Raptorbert
RaptorFun
TanneRd
HighwaySentinel
AmaRaptor
XtraSpclCrspy
whatthetruck
dsg2003mach1
beemerb0y
JD05
kwalker329
BayRaptor925
mprice1234
Ruger
Judd McPherson
BoostCreep
-RRRaptor-
jekyll537
twoputtbirdie
blazn5667
Jesse1983
dmb359
Evasive
mleaky
FP Forged
... and 29 more.
Forum statistics
Threads
93,357
Posts
1,959,579
Members
56,642
Latest member
Jose425316
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford F-150 Raptor General Discussions [GEN 2]
Remi Raptor Build
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top