Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
Ford Raptor Forums - General Information
Off-Roading Your Raptor
Jack Extension for Harbor Frieght Jacks
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Deleted member 12951" data-source="post: 943569"><p>Follow-up: The additional order from Pro Eagle arrived today. [MENTION=9104]Chris's FX4[/MENTION] </p><p></p><p>I first wanted to replace the lift pad on my existing 2ton since those lips where smashed. The Pro Eagle pad center hole is beveled and does not fit around the base. Figure I would buy a Dremel and fix this later.</p><p>BTW: the center pin on the Pro Eagle lift pad comes right out.</p><p></p><p>This is the HF one and how it fits.</p><p>[ATTACH=full]251926[/ATTACH]</p><p>[ATTACH=full]251927[/ATTACH]</p><p></p><p>As you can see the Pro Eagle needs to be bigger. You can screw the center bolt on it but then all the weight is on that edge. Hence why I would have to make the opening larger.</p><p>[ATTACH=full]251928[/ATTACH]</p><p></p><p>Because I want to use these two extensions on my 3ton steel jack and 2ton to be interchangable, I put the other lift pad on it, it fits as that is different without the inner upper lip but even screwed down all the way, its too loose. The center bolt is too long to snug up on it.</p><p>[ATTACH=full]251929[/ATTACH]</p><p>Too much play:</p><p>[ATTACH=full]251930[/ATTACH]</p><p>[ATTACH=full]251931[/ATTACH]</p><p></p><p>So wondering now how to make this work. I took the center bolt from the 2ton and it fits snug and solves the issue! As you see the bolt is not as long.</p><p>[ATTACH=full]251932[/ATTACH]</p><p>[ATTACH=full]251933[/ATTACH]</p><p></p><p>So I move the center bolt from the 3ton to the 2ton just to make sure it fits okay. Too long but expected that. But I was able to stack them by putting the HF pad on first and the Pro Eagle on top of it and it snugged down good.</p><p>[ATTACH=full]251934[/ATTACH]</p><p>Might revisit this of course.</p><p></p><p>Here is with the extensions and I noticed that you can stack them together too.</p><p>[ATTACH=full]251935[/ATTACH]</p><p>[ATTACH=full]251936[/ATTACH]</p><p>[ATTACH=full]251937[/ATTACH]</p><p></p><p>Overall happy with the Pro Eagle decision. Will probably sell my C4fabworks extension now. Last project is to see how I can make the jack mount I purchased can fit on the 2ton. Will post back when I have that done.</p></blockquote><p></p>
[QUOTE="Deleted member 12951, post: 943569"] Follow-up: The additional order from Pro Eagle arrived today. [MENTION=9104]Chris's FX4[/MENTION] I first wanted to replace the lift pad on my existing 2ton since those lips where smashed. The Pro Eagle pad center hole is beveled and does not fit around the base. Figure I would buy a Dremel and fix this later. BTW: the center pin on the Pro Eagle lift pad comes right out. This is the HF one and how it fits. [ATTACH=full]251926[/ATTACH] [ATTACH=full]251927[/ATTACH] As you can see the Pro Eagle needs to be bigger. You can screw the center bolt on it but then all the weight is on that edge. Hence why I would have to make the opening larger. [ATTACH=full]251928[/ATTACH] Because I want to use these two extensions on my 3ton steel jack and 2ton to be interchangable, I put the other lift pad on it, it fits as that is different without the inner upper lip but even screwed down all the way, its too loose. The center bolt is too long to snug up on it. [ATTACH=full]251929[/ATTACH] Too much play: [ATTACH=full]251930[/ATTACH] [ATTACH=full]251931[/ATTACH] So wondering now how to make this work. I took the center bolt from the 2ton and it fits snug and solves the issue! As you see the bolt is not as long. [ATTACH=full]251932[/ATTACH] [ATTACH=full]251933[/ATTACH] So I move the center bolt from the 3ton to the 2ton just to make sure it fits okay. Too long but expected that. But I was able to stack them by putting the HF pad on first and the Pro Eagle on top of it and it snugged down good. [ATTACH=full]251934[/ATTACH] Might revisit this of course. Here is with the extensions and I noticed that you can stack them together too. [ATTACH=full]251935[/ATTACH] [ATTACH=full]251936[/ATTACH] [ATTACH=full]251937[/ATTACH] Overall happy with the Pro Eagle decision. Will probably sell my C4fabworks extension now. Last project is to see how I can make the jack mount I purchased can fit on the 2ton. Will post back when I have that done. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
Butterz
DLarrabee99
scroper
Swifty
Punkur67
hopkintj
MSP
furioussphinx
Sparda1123
GCATX
BBLV
someday
cfmistry
sixshooter_45
BigTaco
thatJeepguy
KMO
RCorsa
Raptor_NV
TomDirt
VJDWashington
kevo_lo
Turning Blue
utahraptor801
k3k0a808
joeyrotorhead
khunter
hanj0208
BoostCreep
catinthehat85
Forum statistics
Threads
93,180
Posts
1,955,505
Members
56,460
Latest member
khunter
Forums
Ford Raptor Forums - General Information
Off-Roading Your Raptor
Jack Extension for Harbor Frieght Jacks
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top