Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
Ford Raptor Forums - General Information
Ford Raptor How-To's and FAQs
DIY: Bed Bolt Removal With Factory Liner + Extra Tie Downs
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="BearLeeAsian" data-source="post: 738780" data-attributes="member: 12850"><p>I am not taking credit for this DIY, did a quick search and have found write ups that I had followed - though I think a better in depth one would suit a beginner DIYer that purchased a Raptor with factory liner.</p><p></p><p></p><p></p><p>This will let you easily remove the bolts that are most likely covered by factory liner + install more mounting points. </p><p></p><p></p><p></p><p>What you will need: </p><p></p><p></p><p></p><p>Chisel</p><p></p><p>Hammer</p><p></p><p>Torx 50 </p><p></p><p>Drill</p><p></p><p>Drill Bit</p><p></p><p>MOPAR RING RETAINERS - Part # 05104500AA</p><p></p><p></p><p></p><p>Use chisel and hammer to easily and quickly remove factory liner.</p><p></p><p></p><p></p><p>[ATTACH=full]236574[/ATTACH]</p><p></p><p>[ATTACH=full]236575[/ATTACH]</p><p></p><p>[ATTACH=full]236576[/ATTACH]</p><p></p><p>[ATTACH=full]236577[/ATTACH]</p><p></p><p></p><p></p><p>Torx Plus 50 to remove the bolt. Once it comes up, you will need to pull it out with the hammer due to the washer attached. It tucks into the bedliner</p><p></p><p>[ATTACH=full]236578[/ATTACH]</p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p>You will need to remove the washer on the bed bolt. Some have used a large socket to remove it. I didn't have one big enough so I went ahead and used a drill and a drill bit to shave off the lips.</p><p></p><p></p><p></p><p>[ATTACH=full]236579[/ATTACH]</p><p></p><p></p><p></p><p>Once removed, sandwich the MOPAR Ring Retainers in the middle. The ring actually has a little lip, make sure it is on the top side, and the flat side is on the bottom. </p><p></p><p></p><p></p><p>[ATTACH=full]236580[/ATTACH]</p><p></p><p></p><p></p><p>Finished product. </p><p></p><p></p><p></p><p>[ATTACH=full]236581[/ATTACH]</p><p></p><p></p><p></p><p>Hope the chisel part helps.</p></blockquote><p></p>
[QUOTE="BearLeeAsian, post: 738780, member: 12850"] I am not taking credit for this DIY, did a quick search and have found write ups that I had followed - though I think a better in depth one would suit a beginner DIYer that purchased a Raptor with factory liner. This will let you easily remove the bolts that are most likely covered by factory liner + install more mounting points. What you will need: Chisel Hammer Torx 50 Drill Drill Bit MOPAR RING RETAINERS - Part # 05104500AA Use chisel and hammer to easily and quickly remove factory liner. [ATTACH=full]236574[/ATTACH] [ATTACH=full]236575[/ATTACH] [ATTACH=full]236576[/ATTACH] [ATTACH=full]236577[/ATTACH] Torx Plus 50 to remove the bolt. Once it comes up, you will need to pull it out with the hammer due to the washer attached. It tucks into the bedliner [ATTACH=full]236578[/ATTACH] You will need to remove the washer on the bed bolt. Some have used a large socket to remove it. I didn't have one big enough so I went ahead and used a drill and a drill bit to shave off the lips. [ATTACH=full]236579[/ATTACH] Once removed, sandwich the MOPAR Ring Retainers in the middle. The ring actually has a little lip, make sure it is on the top side, and the flat side is on the bottom. [ATTACH=full]236580[/ATTACH] Finished product. [ATTACH=full]236581[/ATTACH] Hope the chisel part helps. [/QUOTE]
Insert quotes…
Verification
Post reply
Staff online
Big Blue
Administrator
Members online
Blown00gt
Fireman Dave
east raptor 22
ToadSmasher2K1
never_summer
1BAD454SSv2
Big Blue
ljn21
NickyF25
PK37
Neckface
NASSTY
Pacifico66
valentino 771
Forum statistics
Threads
93,190
Posts
1,955,691
Members
56,469
Latest member
ngodavid23
Forums
Ford Raptor Forums - General Information
Ford Raptor How-To's and FAQs
DIY: Bed Bolt Removal With Factory Liner + Extra Tie Downs
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top