Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Lighting Modifications Forum [GEN 1]
CENTER HOOD MOUNT - 10" KC Flex w/amber cover
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="IRONMAN" data-source="post: 941290" data-attributes="member: 13"><p>I just had my windshield replaced so I had to remove the duals. So I did mount the center light only and yes it looked strange for sure.</p><p>All 3 together do look better then just the center, more complete.</p><p> </p><p></p><p></p><p></p><p></p><p></p><p>I haven't driven it yet to see if it has wind noise but hopefully tomorrow I can test that out.</p><p></p><p>Now the mounting.</p><p>I removed the plastic vent and built / welded up 2 brackets with a 2 1/2" bolt with the threads facing up. The brackets were bolted to the metal frame below then I added / threaded </p><p>two lock nuts with 2 small washers so that they sat just below the plastic vent. The vent had 2 small holes drilled through it to allow the bolts to go through.</p><p>I then made a flat bar brace to span from one side to the other, it sits on the plastic vent. The 10" bar then sits on that bar which helps disperse the stress evenly across the plastic vent.</p><p>Then I bolted it down and ran the power wire through the wiper hole for power.</p></blockquote><p></p>
[QUOTE="IRONMAN, post: 941290, member: 13"] I just had my windshield replaced so I had to remove the duals. So I did mount the center light only and yes it looked strange for sure. All 3 together do look better then just the center, more complete. I haven't driven it yet to see if it has wind noise but hopefully tomorrow I can test that out. Now the mounting. I removed the plastic vent and built / welded up 2 brackets with a 2 1/2" bolt with the threads facing up. The brackets were bolted to the metal frame below then I added / threaded two lock nuts with 2 small washers so that they sat just below the plastic vent. The vent had 2 small holes drilled through it to allow the bolts to go through. I then made a flat bar brace to span from one side to the other, it sits on the plastic vent. The 10" bar then sits on that bar which helps disperse the stress evenly across the plastic vent. Then I bolted it down and ran the power wire through the wiper hole for power. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
Skai
BHook
pirates1456
alockbox
wyomingraptor
Brad_hartpro
SSWIM
Jmeo
RCorsa
hemibob
drnash21
soheilmos
LayinWatts69
Stan Stahr
RaptorJoe331
GCATX
cb35
CVP33
OBXRAPTOR17
Speedhunter
-RRRaptor-
weldoid
Latchkey Kid
tonythis
Stingray23
mwaite09
Eisner62
SilverBolt
ToadSmasher2K1
Derekb95svt
Sozzy12
RockHillRaptor
apollo90
SeasickLI
So-Cal-Al-52
CessnaDriver
JMH2019FPB
HORN HIGH ACES
Armetz
TomDirt
DougDimmadome
Gumby
cdance
elking
tcm glx
stevenstommyboy1
blazn5667
wheelman55
Jsousa03
tabvette
... and 23 more.
Forum statistics
Threads
93,198
Posts
1,955,836
Members
56,485
Latest member
bjorn-dpc
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Lighting Modifications Forum [GEN 1]
CENTER HOOD MOUNT - 10" KC Flex w/amber cover
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top