Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 3 (2021+) Ford F-150 Raptor Forums
Ford Raptor Interior Forum [GEN 3]
Ambient Lighting Installation Part 2
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="FoxNotch" data-source="post: 1877443" data-attributes="member: 63845"><p>Now you need to remove the KV Antenna plug from the piece you just removed. As you can see there are six screws that hold the cup holder in place. The red arrow is the antenna thing you need to switch and the other two red marks are the two center clips that also hold the center trim piece on. As you can see the new cup holder is installed here.</p><p>[ATTACH=full]393266[/ATTACH]</p><p>Now you need to take out the “plug” where the media bin lamp goes, I just pushed it out from the backside, you can reach it behind the shifter. Put the new lamp in from the front side (yellow arrow) you will be able to tell which side is up. Then pull the wires through.</p><p></p><p>[ATTACH=full]393267[/ATTACH]</p><p>The media bin light stays on all the time and plugs in to the center console light thats always on, we are also gonna plug this in to the glovebox light that you’re going to install. The place for the glove box light is empty and is on the top of the glove box opening.</p><p>[ATTACH=full]393311[/ATTACH]</p><p>Run the wires to the left, there is a metal clip and a christmas tree clip that comes on the glovebox lamp, it attaches to the left of the light there is a place just for both of them to clip to. The place for the christmas tree clip is on the inside of the glovebox lip, its where the two wires join(yellow/black-red/black. You kinda have to feel for it with your hand.</p><p>[ATTACH=full]393312[/ATTACH]</p><p>[ATTACH=full]393318[/ATTACH]</p><p>Next, take the felt piece off, below the glovebox/footwell, there is three christmas tree push pins that hold it on, this where you connect the cup holder harness. Both harnesses need to be routed through the center console and to the footwell/glovebox to connect. I will leave the routing to you, obviously you don’t want the harnesses showing.</p><p></p><p>Continued in part 3 thread.</p></blockquote><p></p>
[QUOTE="FoxNotch, post: 1877443, member: 63845"] Now you need to remove the KV Antenna plug from the piece you just removed. As you can see there are six screws that hold the cup holder in place. The red arrow is the antenna thing you need to switch and the other two red marks are the two center clips that also hold the center trim piece on. As you can see the new cup holder is installed here. [ATTACH type="full" alt="F689CF01-88A5-4554-8119-15B2D72C6132.jpeg"]393266[/ATTACH] Now you need to take out the “plug” where the media bin lamp goes, I just pushed it out from the backside, you can reach it behind the shifter. Put the new lamp in from the front side (yellow arrow) you will be able to tell which side is up. Then pull the wires through. [ATTACH type="full" alt="4921146A-81A5-46F6-93A6-2855FFF78F0A.jpeg"]393267[/ATTACH] The media bin light stays on all the time and plugs in to the center console light thats always on, we are also gonna plug this in to the glovebox light that you’re going to install. The place for the glove box light is empty and is on the top of the glove box opening. [ATTACH type="full" alt="056E7B8E-2B1D-4D45-84E0-36BCD35AC273.jpeg"]393311[/ATTACH] Run the wires to the left, there is a metal clip and a christmas tree clip that comes on the glovebox lamp, it attaches to the left of the light there is a place just for both of them to clip to. The place for the christmas tree clip is on the inside of the glovebox lip, its where the two wires join(yellow/black-red/black. You kinda have to feel for it with your hand. [ATTACH type="full" alt="BE5733E2-98D9-45D5-87B6-D1E5D24DF42E.jpeg"]393312[/ATTACH] [ATTACH type="full" alt="E3CF3E8B-8949-47DB-BBDB-3930C2FD3415.jpeg"]393318[/ATTACH] Next, take the felt piece off, below the glovebox/footwell, there is three christmas tree push pins that hold it on, this where you connect the cup holder harness. Both harnesses need to be routed through the center console and to the footwell/glovebox to connect. I will leave the routing to you, obviously you don’t want the harnesses showing. Continued in part 3 thread. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
reesbridges
Raptorman19
ToadSmasher2K1
DrewFish11
SeasickLI
EagleFive
Ruger
TrucksRcool
nelsonr103
nick731
daddyd
Brewski
Jorge Acosta
Jdselig
Sooner89
BenBB
GordoJay
TomDirt
Peterb
MFouts
Whoops
beemerb0y
pirates1456
sparklinghat659
Hambone
Nacho226
tominphx
Gumby
jimmythemannn
dsg2003mach1
TheGrizz
Decoyman
snareplayer121
derise
flyitaway
debauch
Gen1Lucky13SVT
WTX
elpechedepeche
redracer64
SilverBolt
npc
kocher93
jond
OICNW-Rob
Aird_outSRT
stevenstommyboy1
MurderedOutSVT
pat247
xgardx
... and 13 more.
Forum statistics
Threads
93,575
Posts
1,964,187
Members
56,862
Latest member
Bwalt
Forums
GEN 3 (2021+) Ford F-150 Raptor Forums
Ford Raptor Interior Forum [GEN 3]
Ambient Lighting Installation Part 2
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top