Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Lighting Modifications Forum [GEN 1]
Additional LED Grille Markers
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="blclay24" data-source="post: 887261" data-attributes="member: 11964"><p>Sorry for the little delay.. I was in a training class at work.</p><p></p><p>I bought the two grille lights, a harbor freight dremel, and a tube of 5 minute epoxy..</p><p>Started off with the grille still on the truck and carefully dremeled away little by little where the lights will go, stopping and test fitting along the way until it sat where I wanted, then took the grille off the truck and layed it face down on the workbench and masked off where I didn't want epoxy to go (fill the grooves with tape so it stays where you want it), put a few small layers of epoxy, and while it dried I spliced into the main plug, ran the wires, soldered and zip tied, then it was almost set up completely I took some small screws I had laying around and screwed them down in the epoxy..</p><p>One of them didn't hold as good as id hoped so I put a clamp on it for a little while to set up better..</p><p>I was trying to figure out something to put in the channels to act as the OEM clips but I didn't have anything laying around small enough.. The one side still isn't exactly as snug as if like but I'm sure with a little more tweaking it'll stay where I want it..</p></blockquote><p></p>
[QUOTE="blclay24, post: 887261, member: 11964"] Sorry for the little delay.. I was in a training class at work. I bought the two grille lights, a harbor freight dremel, and a tube of 5 minute epoxy.. Started off with the grille still on the truck and carefully dremeled away little by little where the lights will go, stopping and test fitting along the way until it sat where I wanted, then took the grille off the truck and layed it face down on the workbench and masked off where I didn't want epoxy to go (fill the grooves with tape so it stays where you want it), put a few small layers of epoxy, and while it dried I spliced into the main plug, ran the wires, soldered and zip tied, then it was almost set up completely I took some small screws I had laying around and screwed them down in the epoxy.. One of them didn't hold as good as id hoped so I put a clamp on it for a little while to set up better.. I was trying to figure out something to put in the channels to act as the OEM clips but I didn't have anything laying around small enough.. The one side still isn't exactly as snug as if like but I'm sure with a little more tweaking it'll stay where I want it.. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
oliver1539
RCorsa
shigman
24NoVARaptor
Raptor Rob
pirates1456
Otis857
blazn5667
raptor730
TwizzleStix
LayinWatts69
MDRAPTR
jekyll537
Gr8-19SC
mattl600
BadWRP
3wheelkhalil
RaptorJoe331
RaptorAU
DaveInMn
GCATX
fordfreek
RaptorFun
JAYL1985
RHCLLC
HORN HIGH ACES
Hired4bama
Keith88
dillard09
tabvette
Barak
Azurebeast
kknyrass
Jaysun420
Coyote_695
willywilson
Old-Raptor-guy
nikhsub1
2022 Ruth
EliteAGDan
Zeusmotorworks
Tyler James Inc
BoostCreep
sukid
slade8
CleverGirl_
SeasickLI
usafjames
Hard R
zazumanny
... and 14 more.
Forum statistics
Threads
93,186
Posts
1,955,609
Members
56,468
Latest member
ngodavid23
Forums
GEN 1 (2010-2014) Ford SVT Raptor Forums
Ford Raptor Lighting Modifications Forum [GEN 1]
Additional LED Grille Markers
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top